Jump to a service
Arlington, TX
Garage door spring replacement in Arlington, Texas
A broken torsion spring is the most common reason a door stops lifting. The fix is a matched pair sized to what the door actually weighs, not the cheapest spring that fits the shaft.
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
Springs in Arlington
Arlington's ranch stock is unusually consistent, mostly sixteen foot uninsulated steel on standard torsion hardware. Doors of that period are commonly seven feet tall, built from four sections of about twenty one inches. Winding follows door height rather than width: on standard drums a seven foot door takes roughly seven and a half turns, and an eight foot door about a turn more. Turns set the balance, so a correctly sized spring wound short still leaves the door out of balance. A 16 foot torsion assembly rides in an end bearing plate at each side of the opening and usually a center bearing at the anchor bracket. Bearings that have lost their grease squeal on every cycle and let the shaft move in its race. A worn race also lets the shaft wear a groove, and a grooved shaft keeps eating bearings after they are replaced. Usually under two hours from arrival.
What that means for a Arlington door
A 16 foot double door weighs roughly 150 to 250 pounds depending on panel construction, and the torsion assembly above the header carries all of it. Most double doors of this width run a pair of springs on a shared shaft. When one breaks the other is usually near the end of its life, since both were wound the same day and cycled the same number of times. Leftover parts on the horizontal track tell whether a door was converted from extension springs to torsion. Pulley brackets and an empty rear hanger near the back of the track are what stays behind. A conversion brings a shaft, end bearing plates, drums and cables with it, so the hardware above the opening is often newer than the door below it.
Signs you are dealing with this
- The opener strains, hums, or lifts the door a few inches and quits
- The door slams down rather than lowering under control
What we check on arrival
- Whether the existing springs were correctly specified for the door weight
- Cable and drum condition, since a broken spring often damages both
$200 to $450
A standard pair of torsion springs on a two-car door sits mid-range. Oversized, high-cycle or custom-weight doors run higher.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Arlington at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 45 minutes from our Coppell base
- Postcodes covered
- 76001, 76006, 76010, 76012, 76013, 76015, 76016, 76017
- Around
- AT&T Stadium, Globe Life Field, River Legacy Park
Before we get there
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
About Arlington
The 1970s and 1980s ranch stock here is remarkably consistent, mostly sixteen foot uninsulated steel doors.
Tarrant County. About 45 minutes from our Coppell base.
What that means for a door here
Arlington's ranch stock is unusually consistent, mostly sixteen foot uninsulated steel on standard torsion hardware.
We work throughout Arlington, including the neighbourhoods around AT&T Stadium, Globe Life Field, River Legacy Park.
Get a price
Tell us about your Arlington door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 45 minutes away, and Arlington sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Springs in Arlington, asked and answered
Do you cover Arlington?
Yes. Arlington is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 45 minutes from our Coppell base. That covers postcodes 76001, 76006, 76010, 76012, 76013, 76015, 76016, 76017.
What usually fails on a Arlington door?
Anything added to a door changes what the springs have to balance. An insulation kit bonded to the inside of single layer panels adds weight the original spring was not wound for, and so does a replacement section with glass in it. The door usually still opens, but the balance point moves and the opener works harder on every cycle.
How long does garage door spring replacement take in Arlington?
Usually under two hours from arrival. With the trolley released from the opener, a correctly balanced door can be raised by hand with steady effort and will hold position around halfway without being held. A door that sinks or climbs on its own is out of balance, and no adjustment at the opener corrects it. The test only means anything with the opener disconnected.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Arlington?
The 1970s and 1980s ranch stock here is remarkably consistent, mostly sixteen foot uninsulated steel doors. A garage door opener is sized to move a balanced door, not to lift a dead weight. Openers are typically half to three quarter horsepower, which is enough only while the springs carry the door. When a spring weakens, the opener strains, and on older units without modern force sensing it keeps pulling until something in the drive gives out.
Get it fixed
Get a springs price for your Arlington door
Tell us what it is doing. The estimate on site is free.