Jump to a service
Arlington, TX
Garage door tune up and maintenance in Arlington, Texas
A service visit covers rollers, hinges, bearings, spring condition, door balance and the safety reverse. It is the cheapest way to find the part that would otherwise strand somebody.
Tune up in Arlington
Arlington's ranch stock is unusually consistent, mostly sixteen foot uninsulated steel on standard torsion hardware. Steel on a 1970s door was rolled heavier than the sheet on a builder door made now, because material cost fell over the decades between them. The older panel dents less and weighs more, which is why a section swapped in from current stock changes what the counterbalance is holding. Hardware fastener patterns from that period also differ from what a parts shelf carries. Cable drums sit at each end of the torsion shaft and wind the lift cable into a machined groove. Set screws hold each drum to the shaft, and a drum that has crept even slightly leaves one side of the door lifting ahead of the other. The door then tips in the opening and the low side cable goes slack at the top of travel. About an hour for one door.
What that means for a Arlington door
Hail damage on a steel door goes past appearance. Dents across a section stiffen it in some places and weaken it in others, and a section that no longer sits flat puts uneven load on the hinges between it and the section next to it. Checking hinge leaves for elongated holes and the top section for a bowed strut is the useful follow up after a storm. Service interval tracks cycles, not years. A door on a rental or a shared drive that opens eight or ten times a day reaches a spring's rated cycle count in a fraction of the time a four cycle a day household door takes. Two identical doors installed the same week can be years apart in remaining spring life.
Signs you are dealing with this
- The door shudders or hesitates at the same point in its travel
- You want to know how much life the springs have left
What we check on arrival
- Safety reverse tested against a physical obstruction
- Photo eye alignment, opener force settings and travel limits
$99 to $199
One door is at the low end. Multiple doors on the same visit are discounted per door.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Arlington at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 45 minutes from our Coppell base
- Postcodes covered
- 76001, 76006, 76010, 76012, 76013, 76015, 76016, 76017
- Around
- AT&T Stadium, Globe Life Field, River Legacy Park
Before we get there
Lubricate rollers, hinges and springs, never the tracks. Grease on a track collects grit and wears rollers faster than no lubricant at all.
About Arlington
The 1970s and 1980s ranch stock here is remarkably consistent, mostly sixteen foot uninsulated steel doors.
Tarrant County. About 45 minutes from our Coppell base.
What that means for a door here
Arlington's ranch stock is unusually consistent, mostly sixteen foot uninsulated steel on standard torsion hardware.
We work throughout Arlington, including the neighbourhoods around AT&T Stadium, Globe Life Field, River Legacy Park.
Get a price
Tell us about your Arlington door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 45 minutes away, and Arlington sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Tune up in Arlington, asked and answered
Do you cover Arlington?
Yes. Arlington is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 45 minutes from our Coppell base. That covers postcodes 76001, 76006, 76010, 76012, 76013, 76015, 76016, 76017.
What usually fails on a Arlington door?
Perimeter seal is a vinyl or rubber strip in a stop molding nailed to the jamb and header, and it seats against the outside face of the door. Nails back out and the molding twists after enough seasons of sun. A gap at the top corners is usually the molding rather than the door, and it is the path wind driven rain takes.
How long does garage door tune up and maintenance take in Arlington?
About an hour for one door. The safety reverse test uses a solid object laid on the floor in the door's path. A length of two by four laid flat works. The door should contact it and reverse promptly. If it keeps pushing down or reverses only after visible pressure, the down force setting or the travel limit is out of adjustment, and that is a fault to correct before the door is used again.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Arlington?
The 1970s and 1980s ranch stock here is remarkably consistent, mostly sixteen foot uninsulated steel doors. Steel rollers with exposed bearings are common on light gauge steel doors and they announce wear by rumbling, then by a dry metallic rattle once the bearing loses its grease. Nylon rollers fail differently. The tire wears flat or cracks at the stem, so the sound is a rhythmic slap or a thump once per revolution rather than a grind.
Get it fixed
Get a tune up price for your Arlington door
Tell us what it is doing. The estimate on site is free.