Jump to a service
Arlington, TX
Commercial garage door service in Arlington, Texas
Rolling steel, sectional and dock equipment fail differently from a house door, because they cycle twenty or thirty times a day rather than four. Downtime, not the part, is usually the real cost.
A rolling steel door carries its spring inside the barrel at a tension far above a residential torsion spring. Barrel work is not a maintenance task.
Commercial in Arlington
Arlington's ranch stock is unusually consistent, mostly sixteen foot uninsulated steel on standard torsion hardware. Shop and workshop doors of that age were often hung on three inch track where a house door uses two inch, and the two families do not share rollers or hinges. A roller stem cut for the narrower channel rattles in the wider one. Track width is read across the open face of the channel before any hardware is ordered. Timer to close holds a door open for a set interval and then closes it with nobody at the controls. That mode calls for monitored entrapment protection and a warning device that runs before travel starts, because the person in the opening has no reason to expect movement. Disabling the timer is the correct response to a failed sensing device, rather than bypassing the device. Varies by door type, quoted after the site assessment.
What that means for a Arlington door
Panel steel is described by gauge, and a lower gauge number means thicker steel. Commercial specification doors move down the gauge scale and add reinforcing struts because the load they take is impact rather than wind. A door bought on width and height alone can arrive in a lighter gauge than the previous one and dent under handling the building has always given it. Steel guard posts set in concrete either side of an opening take the hit that would otherwise land on the jamb and the vertical track. On a bay used by forklifts or delivery vans, the damage pattern is repetitive and low down. A bent lower track section is repairable; a jamb pushed out of plumb takes the whole door out of alignment.
Signs you are dealing with this
- A dock or bay door is stuck open and the building is not secure
- A rolling steel door has jammed partway in its curtain
What we check on arrival
- Operator type, wiring, and control station or sensor faults
- Counterbalance spring tension against the actual door weight
$300 to $6000
A service call and adjustment is at the low end. Rolling steel door replacement and dock equipment work runs to the top of the range and beyond.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Arlington at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 45 minutes from our Coppell base
- Postcodes covered
- 76001, 76006, 76010, 76012, 76013, 76015, 76016, 76017
- Around
- AT&T Stadium, Globe Life Field, River Legacy Park
Before we get there
A rolling steel door carries its spring inside the barrel at a tension far above a residential torsion spring. Barrel work is not a maintenance task.
About Arlington
The 1970s and 1980s ranch stock here is remarkably consistent, mostly sixteen foot uninsulated steel doors.
Tarrant County. About 45 minutes from our Coppell base.
What that means for a door here
Arlington's ranch stock is unusually consistent, mostly sixteen foot uninsulated steel on standard torsion hardware.
We work throughout Arlington, including the neighbourhoods around AT&T Stadium, Globe Life Field, River Legacy Park.
Get a price
Tell us about your Arlington door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 45 minutes away, and Arlington sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Commercial in Arlington, asked and answered
Do you cover Arlington?
Yes. Arlington is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 45 minutes from our Coppell base. That covers postcodes 76001, 76006, 76010, 76012, 76013, 76015, 76016, 76017.
What usually fails on a Arlington door?
Steel door skins are galvanized before they are painted, so corrosion starts where the coating is broken rather than across the face. Cut edges at the bottom section and drilled screw holes are the two places to look. In a wash bay or a shop with humid air the lower section rusts from the inside face outward, and the paint hides it until the skin blisters.
How long does commercial garage door service take in Arlington?
Varies by door type, quoted after the site assessment. A house door runs about four cycles a day. A door on a working unit can run twenty or thirty, which is a different machine even when the hardware looks identical. Rollers, hinges, cables and the spring all reach their rated life in a small fraction of the calendar time, and the components that fail first are the ones with a bearing surface in them.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Arlington?
The 1970s and 1980s ranch stock here is remarkably consistent, mostly sixteen foot uninsulated steel doors. A sensing edge runs the full width of the bottom section and reverses the door when it is compressed by anything in the opening. It is standard on commercial operators where a photo beam alone cannot see a low object across a wide bay. The edge is wired back to the operator through a coil cord or a wireless transmitter, and both wear at the door end.
Get it fixed
Get a commercial price for your Arlington door
Tell us what it is doing. The estimate on site is free.