Jump to a service
Bedford, TX
Garage door spring replacement in Bedford, Texas
A broken torsion spring is the most common reason a door stops lifting. The fix is a matched pair sized to what the door actually weighs, not the cheapest spring that fits the shaft.
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
Springs in Bedford
Bedford is dominated by standard sixteen foot openings, which means parts availability is rarely what decides how quickly a repair finishes. Some doors of that period carry an enclosed counterbalance, with the torsion spring running inside a steel tube above the opening and wound through a fitting at one end rather than with bars. A spring that fails inside the tube leaves nothing visible from the floor. The first sign is a door the opener can no longer lift. A wood door that is still original has not weighed the same all its life. Timber takes on moisture in a damp garage and gives it back in dry months, and layers of paint add to the section over the years. The spring was wound for the door as it left the shop. The same door can sit differently in a wet season than in a dry one. Usually under two hours from arrival.
What that means for a Bedford door
A garage door opener is sized to move a balanced door, not to lift a dead weight. Openers are typically half to three quarter horsepower, which is enough only while the springs carry the door. When a spring weakens, the opener strains, and on older units without modern force sensing it keeps pulling until something in the drive gives out. Doors of that period are commonly seven feet tall, built from four sections of about twenty one inches. Winding follows door height rather than width: on standard drums a seven foot door takes roughly seven and a half turns, and an eight foot door about a turn more. Turns set the balance, so a correctly sized spring wound short still leaves the door out of balance.
Signs you are dealing with this
- The door is far too heavy to lift by hand
- The opener strains, hums, or lifts the door a few inches and quits
What we check on arrival
- Center bearing plate and end bearing wear
- Door balance after installation, tested by hand at three heights
$200 to $450
A standard pair of torsion springs on a two-car door sits mid-range. Oversized, high-cycle or custom-weight doors run higher.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Bedford at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 30 minutes from our Coppell base
- Postcodes covered
- 76021, 76022
- Around
- Boys Ranch Park, Bedford Splash, Old Bedford School
Before we get there
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
About Bedford
Standard sixteen foot two car openings dominate here, so replacement parts are rarely a sourcing problem.
Tarrant County. About 30 minutes from our Coppell base.
What that means for a door here
Bedford is dominated by standard sixteen foot openings, which means parts availability is rarely what decides how quickly a repair finishes.
We work throughout Bedford, including the neighbourhoods around Boys Ranch Park, Bedford Splash, Old Bedford School.
Get a price
Tell us about your Bedford door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 30 minutes away, and Bedford sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Springs in Bedford, asked and answered
Do you cover Bedford?
Yes. Bedford is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 30 minutes from our Coppell base. That covers postcodes 76021, 76022.
What usually fails on a Bedford door?
A broken torsion spring shows as a gap of an inch or two in the coil, usually visible from the floor by looking at the shaft above the door. The break often announces itself as a single loud bang from an empty garage. After it, the opener may hum and move the trolley while the door stays on the floor.
How long does garage door spring replacement take in Bedford?
Usually under two hours from arrival. Anything added to a door changes what the springs have to balance. An insulation kit bonded to the inside of single layer panels adds weight the original spring was not wound for, and so does a replacement section with glass in it. The door usually still opens, but the balance point moves and the opener works harder on every cycle.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Bedford?
Standard sixteen foot two car openings dominate here, so replacement parts are rarely a sourcing problem. A door that runs away from the floor and slaps into the top of its travel is carrying more spring than its weight calls for. At the top the cables go slack on the drums and can jump the groove, and the top section takes the shock each cycle. The mismatch usually traces back to a spring chosen by door size rather than by measured panel weight.
Get it fixed
Get a springs price for your Bedford door
Tell us what it is doing. The estimate on site is free.