Jump to a service
Arlington, TX
Garage door cable and track repair in Arlington, Texas
A door hanging crooked, off its rail, or with a cable coiled at the bottom bracket is carrying its load somewhere it was not designed to. That is not a door to keep operating.
A door off its track can fall. Do not run the opener to try to correct it, and keep people and vehicles out from under it until it is secured.
Cables and track in Arlington
Arlington's ranch stock is unusually consistent, mostly sixteen foot uninsulated steel on standard torsion hardware. Track is bent steel channel with no moving parts, and a straight length of it from the 1980s does the same job now as it did then. What wears is everything that touches it: roller wheels and hinge pivots. A door of that age often needs those parts and nothing else, provided the channel is still straight and square to the opening. Steel rollers with exposed bearings were standard on older installations and wear into an oval, which lets the stem drop in the track. Nylon rollers on sealed bearings run quieter and hold shape longer. Roller stems also bend when a door is forced against an obstruction, and a bent stem walks the roller out of the track on the next cycle. Most track and cable work is one to two hours.
What that means for a Arlington door
Hail leaves dimples across the face of steel sections, and cosmetic dimpling on the flat of a panel does not change how the door runs. What matters for travel is the end stile and the edge of the section, where a hard hit can twist the metal the hinge and roller carrier are bolted to. A section that now leads on one side is bent at the stile. Lift cables are galvanized aircraft cable, and the diameter is chosen for the weight hanging on it. Wear shows first as broken strands, usually at the loop over the bottom bracket pin or at the first wrap on the drum. A cable with one strand gone is on its way out, and the pair is replaced together because both have run the same cycles.
Signs you are dealing with this
- Rollers are jumping out of the rail at the curve
- The rail has a visible bend or a gap at a joint
What we check on arrival
- Roller stems and bearings on every hinge position
- Bottom bracket condition, which is under permanent tension
$150 to $450
Resetting a door on its track with new rollers is at the low end. Replacing cables, drums and a bent rail section is at the high end.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Arlington at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 45 minutes from our Coppell base
- Postcodes covered
- 76001, 76006, 76010, 76012, 76013, 76015, 76016, 76017
- Around
- AT&T Stadium, Globe Life Field, River Legacy Park
Before we get there
A door off its track can fall. Do not run the opener to try to correct it, and keep people and vehicles out from under it until it is secured.
About Arlington
The 1970s and 1980s ranch stock here is remarkably consistent, mostly sixteen foot uninsulated steel doors.
Tarrant County. About 45 minutes from our Coppell base.
What that means for a door here
Arlington's ranch stock is unusually consistent, mostly sixteen foot uninsulated steel on standard torsion hardware.
We work throughout Arlington, including the neighbourhoods around AT&T Stadium, Globe Life Field, River Legacy Park.
Get a price
Tell us about your Arlington door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 45 minutes away, and Arlington sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Cables and track in Arlington, asked and answered
Do you cover Arlington?
Yes. Arlington is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 45 minutes from our Coppell base. That covers postcodes 76001, 76006, 76010, 76012, 76013, 76015, 76016, 76017.
What usually fails on a Arlington door?
A cable coiled loose at the bottom bracket lost tension while the door was moving. That happens when the door lands on an obstruction and one side keeps unwinding, or when a spring breaks mid travel. Rewinding the same cable ignores why it came off, since a scored drum or a bent bottom bracket will unseat it again.
How long does garage door cable and track repair take in Arlington?
Most track and cable work is one to two hours. A 16 foot door runs a cable and a drum at each end of the torsion shaft, and both drums have to hold the same number of wraps. If one set screw slips, that side rises faster, the door racks in the opening, and a roller leaves the track. Correcting it means resetting the wrap count on both drums, since the track itself is often undamaged.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Arlington?
The 1970s and 1980s ranch stock here is remarkably consistent, mostly sixteen foot uninsulated steel doors. Single layer steel sections dent easily, and a dent along the bottom edge or a stile can be enough to bind a roller. Light gauge track bends rather than absorbing a hit, so a vehicle bumping the door often leaves the panel and the vertical track out of line. Straightening a kinked track with pliers leaves a high spot that catches every cycle.
Get it fixed
Get a cables and track price for your Arlington door
Tell us what it is doing. The estimate on site is free.