Jump to a service
Dallas County, TX
Garage door repair in Irving, Texas
Most faults announce themselves before they strand anyone. A door that hesitates, reverses part way down or runs crooked is naming a specific failed component, and the diagnosis decides the repair rather than the other way round.
If the door is stuck part way and you can hear tension in the springs, leave it alone. A door under load can drop without warning.
Garage doors in Irving
South and central Irving hold a lot of single-width doors and older chain drive openers with no rolling code security. A good share of south and central Irving still runs openers that predate 1993, which is the year photo eye entrapment protection became mandatory. Steel doors of the 1980s were finished with air dried paint over a light primer rather than the baked coatings used later, so the topcoat chalks and thins under sun. Rust starts at the bottom section where the panel meets a damp slab and works up from the cut edge inward. Once the lowest section perforates around the bracket, refinishing no longer restores it.
Garage doors in Irving
Steel rollers with plain stems were the builder default into the 1980s, running on exposed ball races that collect grit and eventually seize. A seized roller slides instead of turning and polishes a bright stripe along the track. Nylon wheels on sealed bearings replaced them later, and stem length and diameter still have to match the hinge the roller sits in. Cable drums are grooved castings keyed to the torsion shaft, and both have to hold the same length of cable for the door to sit level. A drum that has slipped leaves one side riding high, which pinches rollers on the low side and puts a diagonal crease across the bottom section. Worn grooves let the cable cut its own path and fray.
Start here
What is the door in Irving doing?
You do not need to know the name of the part. Find the line that matches and we will take it from there.
- There was a bang like a gunshot and now it will not lift That noise is nearly always a torsion spring letting go Garage door spring replacement in Irving
- The motor runs but the door does not move Usually a stripped drive gear or a trolley that has come disconnected Garage door opener repair and installation in Irving
- It closes most of the way then goes back up Almost always the photo eyes near the floor, or a travel limit setting Garage door opener repair and installation in Irving
- It is hanging crooked, or one side has come off the rail A cable, roller or track problem. The door is carrying load somewhere it should not Garage door cable and track repair in Irving
- There is a cable dangling or coiled up at the bottom A lift cable has come off its drum or snapped, so the two sides are no longer balanced Garage door cable and track repair in Irving
- It opens a few inches then stops Could be spring tension, a track obstruction or a force setting. It needs looking at rather than guessing Garage door repair in Irving
- One side lifts faster than the other Uneven lift means one cable or drum is out of adjustment Garage door cable and track repair in Irving
- Something hit it and there is a dent in one section Often one panel rather than a whole door, depending on whether that section is still made Garage door panel replacement in Irving
- It has got really loud over the last year Worn roller bearings and dry hinges, not the motor Garage door tune up and maintenance in Irving
- It works from the wall button but not the remote Remote, receiver or antenna rather than the door itself Garage door opener repair and installation in Irving
- It will not stay open, it slides back down on its own The springs are no longer counterbalancing the door weight Garage door spring replacement in Irving
- The door is old, ugly, and the garage is unbearable in summer An insulated replacement, and the measuring comes before the catalogue New garage door installation in Irving
- Nothing has broken but it has never been serviced The cheapest visit there is, and the one that finds the thing that would have stranded you Garage door tune up and maintenance in Irving
- A bay door or dock door has stopped at our premises Rolling steel, sectional and dock equipment, where downtime usually costs more than the part Commercial garage door service in Irving
What we work on in Irving
- Same day Garage door spring replacement in Irving $200 to $450 Details
- Garage door opener repair and installation in Irving $175 to $700 Details
- New garage door installation in Irving $1100 to $4500 Details
- Same day Garage door cable and track repair in Irving $150 to $450 Details
- Garage door panel replacement in Irving $350 to $1400 Details
- Garage door tune up and maintenance in Irving $99 to $199 Details
- Same day Commercial garage door service in Irving $300 to $6000 Details
Irving at a glance
- County
- Dallas County
- Drive from our Coppell base
- About 15 minutes from our Coppell base
- Postcodes covered
- 75038, 75060, 75061, 75062
- Around
- Irving Heritage District, Toyota Music Factory, Irving Mall
About Irving
South and central Irving hold a lot of single-width doors and older chain drive openers with no rolling code security.
Dallas County. About 15 minutes from our Coppell base.
What that means for a door here
A good share of south and central Irving still runs openers that predate 1993, which is the year photo eye entrapment protection became mandatory.
We work throughout Irving, including the neighbourhoods around Irving Heritage District, Toyota Music Factory, Irving Mall.
Get a price
Tell us about your Irving door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 15 minutes away, and Irving sits in Dallas County.
A person answers 7am to 11pm.
Questions
Garage door repair in Irving, asked and answered
Do you cover Irving?
Yes. Irving is in Dallas County, and it is one of the 32 cities covered from the Coppell base. About 15 minutes from our Coppell base. That covers postcodes 75038, 75060, 75061, 75062.
What usually fails on a Irving door?
Extension spring systems of the 1970s route each cable over a sheave at the moving end of the spring and another at the rear track hanger. Those pulleys carry the full load and their bushings wear oval, which lets a cable jump the groove. S hooks at the anchor end were often opened and reused, and a hook spread once will not close to its original grip.
How long does garage door repair take in Irving?
Most repairs take one to two hours on site. An opening framed in the 1960s or 1970s is usually on its second or third door, and each change left its own pattern of lag holes in the jamb. A bracket fastened into an old hole feels tight and holds nothing, because the threads have no fresh wood to bite. Fastener positions get moved onto sound material rather than reused.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Irving?
South and central Irving hold a lot of single-width doors and older chain drive openers with no rolling code security. Single layer steel has a thin skin and no backing, so damage shows as denting and as section edges that flex where a strut should be. Hinge holes elongate at the end stiles because there is little metal around them. The door stays light, which keeps spring and opener load low but does nothing for panel stiffness.
Get it fixed
A door in Irving that will not behave?
About 15 minutes from our Coppell base. The estimate on site is free.