Jump to a service
Arlington, TX
Garage door panel replacement in Arlington, Texas
One damaged section can often be swapped without replacing the whole door. Whether it can comes down to whether the manufacturer still makes that panel, in that design, in that colour.
Panels in Arlington
Arlington's ranch stock is unusually consistent, mostly sixteen foot uninsulated steel on standard torsion hardware. Openers added to doors of the 1980s were frequently bolted through the top section skin with no reinforcement bracket behind it, because the door had not been built with an operator in mind. The holes elongate and the steel tears around them. A section replaced for that reason takes a proper strut and bracket, or the new panel goes the same way. A bent section often shows up as an opener complaint. The door reverses partway down or stalls at the same point every time, because the damaged section binds where the track curves. Pulling the release handle and moving the door manually separates the two. A door that sticks at the same height with the motor disconnected has a section or track fault. A single panel swap is usually two to three hours.
What that means for a Arlington door
Hail dents a single layer steel door because the skin is the only thing between the stone and open air behind it. A strike that lands between struts pushes the steel in and it stays in, since there is no core to spread the load. The dimples read most clearly on a flat or lightly embossed panel, where no stamped pattern breaks up the reflection. Steel that has been stretched by an impact will not come back to its original shape, which is the line between pushing a shallow dimple out and replacing the section. A crease that runs across a stamped rib has stretched the metal along that line. Filler bridges the low spot but sits on a panel that flexes every cycle, so it eventually cracks at the edge.
Signs you are dealing with this
- A vehicle backed into the bottom section
- Hail has dimpled one or two panels but the rest are sound
What we check on arrival
- Colour and finish match against the weathered existing sections
- Whether the impact also bent track or knocked the door out of alignment
$350 to $1400
One section on a common current door line is at the low end. Multiple sections, or a discontinued design that needs a full-door match, runs higher.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Arlington at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 45 minutes from our Coppell base
- Postcodes covered
- 76001, 76006, 76010, 76012, 76013, 76015, 76016, 76017
- Around
- AT&T Stadium, Globe Life Field, River Legacy Park
Before we get there
A dented section can hide a bent strut or hinge behind it. Replacing the skin without checking the structure puts the load back onto damaged parts.
About Arlington
The 1970s and 1980s ranch stock here is remarkably consistent, mostly sixteen foot uninsulated steel doors.
Tarrant County. About 45 minutes from our Coppell base.
What that means for a door here
Arlington's ranch stock is unusually consistent, mostly sixteen foot uninsulated steel on standard torsion hardware.
We work throughout Arlington, including the neighbourhoods around AT&T Stadium, Globe Life Field, River Legacy Park.
Get a price
Tell us about your Arlington door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 45 minutes away, and Arlington sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Panels in Arlington, asked and answered
Do you cover Arlington?
Yes. Arlington is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 45 minutes from our Coppell base. That covers postcodes 76001, 76006, 76010, 76012, 76013, 76015, 76016, 76017.
What usually fails on a Arlington door?
Whether a single section can be ordered starts with the manufacturer label, usually a sticker on the inside of the top or bottom section near an end stile. It carries the maker, the model line and a date, and without it the door has to be identified from panel profile and hardware alone. A door still in production is the straightforward case.
How long does garage door panel replacement take in Arlington?
A single panel swap is usually two to three hours. Replacing a section changes the weight of the door slightly, and an insulated replacement in a run of single layer sections changes it more. Openers installed before 1993 predate the requirement for photo eyes in the United States, so the only obstruction protection is the force setting, which was tuned to the door as it was. Force and limits are worth rechecking after the section goes in.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Arlington?
The 1970s and 1980s ranch stock here is remarkably consistent, mostly sixteen foot uninsulated steel doors. Fiberglass faced doors were sold through the 1970s, often with translucent panels that let daylight into the garage. Sun makes the resin yellow and go brittle, so a panel that survived intact can crack while it is being handled. Nothing current is made to those panel sizes, which leaves rebuilding the frame with new material or changing the door.
Get it fixed
Get a panels price for your Arlington door
Tell us what it is doing. The estimate on site is free.