Jump to a service
Keller, TX
Garage door spring replacement in Keller, Texas
A broken torsion spring is the most common reason a door stops lifting. The fix is a matched pair sized to what the door actually weighs, not the cheapest spring that fits the shaft.
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
Springs in Keller
A shop or outbuilding door in Keller is often taller than the standard seven or eight feet, which means high lift track rather than a standard radius. Wind load ratings moved into building codes after the storm damage of the early 1990s, and doors built to them became common through the following decade. A rated door carries extra struts across the sections and heavier end stiles. That steel adds weight over an unrated door of the same width, and the springs are wound for the door as it was actually built. The red release cord drops the door off the opener trolley so it can be worked by hand. With a broken spring, that hand is holding the whole door, and a double door in that state is beyond what one person should lift. A door already up when the spring fails should be left up and blocked rather than pulled down. Usually under two hours from arrival.
What that means for a Keller door
An insulated steel door carries polystyrene or polyurethane between two skins, which adds weight over a single layer panel of identical width. Springs have to be wound for that extra load. Fitting a spring specified for a lighter door leaves the door heavy at the floor and drifting closed from waist height, and it shortens the opener's working life. A door that runs away from the floor and slaps into the top of its travel is carrying more spring than its weight calls for. At the top the cables go slack on the drums and can jump the groove, and the top section takes the shock each cycle. The mismatch usually traces back to a spring chosen by door size rather than by measured panel weight.
Signs you are dealing with this
- The opener strains, hums, or lifts the door a few inches and quits
- The door slams down rather than lowering under control
What we check on arrival
- Whether the existing springs were correctly specified for the door weight
- Cable and drum condition, since a broken spring often damages both
$200 to $450
A standard pair of torsion springs on a two-car door sits mid-range. Oversized, high-cycle or custom-weight doors run higher.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Keller at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 35 minutes from our Coppell base
- Postcodes covered
- 76244, 76248
- Around
- Keller Town Center, Bear Creek Park, The Keller Pointe
Before we get there
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
About Keller
Outbuildings and shop garages here often need a door taller than the standard seven or eight feet.
Tarrant County. About 35 minutes from our Coppell base.
What that means for a door here
A shop or outbuilding door in Keller is often taller than the standard seven or eight feet, which means high lift track rather than a standard radius.
We work throughout Keller, including the neighbourhoods around Keller Town Center, Bear Creek Park, The Keller Pointe.
Get a price
Tell us about your Keller door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 35 minutes away, and Keller sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Springs in Keller, asked and answered
Do you cover Keller?
Yes. Keller is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 35 minutes from our Coppell base. That covers postcodes 76244, 76248.
What usually fails on a Keller door?
Spring life is counted in cycles rather than years, where one cycle is a full open and close. A house that uses the garage as its main entrance can run eight cycles a day, which works through a 10,000 cycle spring in three to four years. The same spring on a door opened twice a day lasts well over a decade.
How long does garage door spring replacement take in Keller?
Usually under two hours from arrival. Torsion springs are handed. A left wound spring and a right wound spring are not interchangeable, and the winding cones are commonly colored to show which is which, red for left wound and black for right wound. On a two spring shaft one of each is fitted, mounted either side of the center bracket, so a matched pair means matched in hand as well as in size.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Keller?
Outbuildings and shop garages here often need a door taller than the standard seven or eight feet. Oversized openings past the common 16 foot width put more panel weight on the same shaft, and the spring has to be wound for it. Wider doors also flex more across the middle, which is why many carry a strut on the top section. Spring length and wire size both change with the weight, and a longer shaft may need a center bearing plate.
Get it fixed
Get a springs price for your Keller door
Tell us what it is doing. The estimate on site is free.