Jump to a service
Southlake, TX
Garage door spring replacement in Southlake, Texas
A broken torsion spring is the most common reason a door stops lifting. The fix is a matched pair sized to what the door actually weighs, not the cheapest spring that fits the shaft.
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
Springs in Southlake
A wood overlay door in Southlake can weigh two to three times a standard steel one, which changes the spring calculation completely rather than slightly. The red release cord drops the door off the opener trolley so it can be worked by hand. With a broken spring, that hand is holding the whole door, and a double door in that state is beyond what one person should lift. A door already up when the spring fails should be left up and blocked rather than pulled down. A three bay elevation with two singles and a double needs more than one spring specification. The double is roughly twice the weight of each single, so the shafts carry different springs even though the doors were installed together and look alike from the street. Replacing all three with the same part leaves two of them out of balance. Usually under two hours from arrival.
What that means for a Southlake door
Weight is the input that decides a torsion spring, and on a heavy door it is measured rather than estimated. A scale under the door with the springs disconnected gives the number. From there the wire diameter and spring length are matched to it. A door that fights the opener at head height is usually carrying a spring wound for something lighter. A broken torsion spring shows as a gap of an inch or two in the coil, usually visible from the floor by looking at the shaft above the door. The break often announces itself as a single loud bang from an empty garage. After it, the opener may hum and move the trolley while the door stays on the floor.
Signs you are dealing with this
- The opener strains, hums, or lifts the door a few inches and quits
- The door slams down rather than lowering under control
What we check on arrival
- Cable and drum condition, since a broken spring often damages both
- Center bearing plate and end bearing wear
$200 to $450
A standard pair of torsion springs on a two-car door sits mid-range. Oversized, high-cycle or custom-weight doors run higher.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Southlake at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 25 minutes from our Coppell base
- Postcodes covered
- 76092
- Around
- Southlake Town Square, Bob Jones Nature Center, Grapevine Lake
Before we get there
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
About Southlake
Custom and wood overlay doors here can weigh two to three times what a standard steel door weighs.
Tarrant County. About 25 minutes from our Coppell base.
What that means for a door here
A wood overlay door in Southlake can weigh two to three times a standard steel one, which changes the spring calculation completely rather than slightly.
We work throughout Southlake, including the neighbourhoods around Southlake Town Square, Bob Jones Nature Center, Grapevine Lake.
Get a price
Tell us about your Southlake door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 25 minutes away, and Southlake sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Springs in Southlake, asked and answered
Do you cover Southlake?
Yes. Southlake is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 25 minutes from our Coppell base. That covers postcode 76092.
What usually fails on a Southlake door?
Oversized openings past the common 16 foot width put more panel weight on the same shaft, and the spring has to be wound for it. Wider doors also flex more across the middle, which is why many carry a strut on the top section. Spring length and wire size both change with the weight, and a longer shaft may need a center bearing plate.
How long does garage door spring replacement take in Southlake?
Usually under two hours from arrival. Spring life is counted in cycles rather than years, where one cycle is a full open and close. A house that uses the garage as its main entrance can run eight cycles a day, which works through a 10,000 cycle spring in three to four years. The same spring on a door opened twice a day lasts well over a decade.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Southlake?
Custom and wood overlay doors here can weigh two to three times what a standard steel door weighs. A wood overlay or custom door can weigh two to three times what a standard steel door of the same opening weighs. Spring sizing follows the weight on a scale, not the width and height on a tape measure. Doors like this often need heavier wire or a longer spring than the width alone would suggest, and sometimes a pair where a steel door would balance on one.
Get it fixed
Get a springs price for your Southlake door
Tell us what it is doing. The estimate on site is free.