Jump to a service
Westlake, TX
Garage door spring replacement in Westlake, Texas
A broken torsion spring is the most common reason a door stops lifting. The fix is a matched pair sized to what the door actually weighs, not the cheapest spring that fits the shaft.
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
Springs in Westlake
A Westlake elevation can carry standard, oversized and RV height doors side by side, each with its own spring, track and opener specification. A three bay elevation with two singles and a double needs more than one spring specification. The double is roughly twice the weight of each single, so the shafts carry different springs even though the doors were installed together and look alike from the street. Replacing all three with the same part leaves two of them out of balance. Doors built from the 2000s onward usually carry a manufacturer label inside an end stile or on the back of a section, listing model and serial. That label is the shortest route back to the original hardware specification, including the counterbalance the door left the factory with. Paint on the outside face does not touch it. Usually under two hours from arrival.
What that means for a Westlake door
Battery backup has become common on residential openers over the past decade, and some states now require it on new units. The battery keeps the trolley moving when the power is out. It does nothing for balance. A door left with a failed spring still weighs its full weight, and a motor of ordinary residential size is not built to raise that. A wood overlay or custom door can weigh two to three times what a standard steel door of the same opening weighs. Spring sizing follows the weight on a scale, not the width and height on a tape measure. Doors like this often need heavier wire or a longer spring than the width alone would suggest, and sometimes a pair where a steel door would balance on one.
Signs you are dealing with this
- A loud bang from the garage, then the door will not open
- A visible gap in the coil of the spring above the door
What we check on arrival
- Spring wire size, inside diameter and length to confirm correct sizing
- Whether the existing springs were correctly specified for the door weight
$200 to $450
A standard pair of torsion springs on a two-car door sits mid-range. Oversized, high-cycle or custom-weight doors run higher.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Westlake at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 30 minutes from our Coppell base
- Postcodes covered
- 76262
- Around
- Vaquero, Solana, Westlake Academy
Before we get there
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
About Westlake
Multi bay estate garages here frequently combine standard, oversized and RV height doors on the same elevation.
Tarrant County. About 30 minutes from our Coppell base.
What that means for a door here
A Westlake elevation can carry standard, oversized and RV height doors side by side, each with its own spring, track and opener specification.
We work throughout Westlake, including the neighbourhoods around Vaquero, Solana, Westlake Academy.
Get a price
Tell us about your Westlake door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 30 minutes away, and Westlake sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Springs in Westlake, asked and answered
Do you cover Westlake?
Yes. Westlake is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 30 minutes from our Coppell base. That covers postcode 76262.
What usually fails on a Westlake door?
Oversized openings past the common 16 foot width put more panel weight on the same shaft, and the spring has to be wound for it. Wider doors also flex more across the middle, which is why many carry a strut on the top section. Spring length and wire size both change with the weight, and a longer shaft may need a center bearing plate.
How long does garage door spring replacement take in Westlake?
Usually under two hours from arrival. Doors serving rentals and small commercial buildings run more cycles per year than an owner occupied single family garage. Spring wear tracks cycle count, so the same part fails sooner under that pattern. A high cycle spring uses heavier wire on a larger inside diameter to carry the same door weight for more openings before fatigue sets in.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Westlake?
Multi bay estate garages here frequently combine standard, oversized and RV height doors on the same elevation. RV height doors add sections above the standard seven or eight foot opening, so the cable has to travel farther and the drum takes more wraps. That extra travel changes how many turns the spring needs and often calls for a larger drum. A spring sized from door width alone will leave a taller door unbalanced through part of its travel.
Get it fixed
Get a springs price for your Westlake door
Tell us what it is doing. The estimate on site is free.