Jump to a service
Keller, TX
New garage door installation in Keller, Texas
A replacement door is a measuring job before it is a shopping decision. Opening width, headroom, backroom and the weight of the door chosen all decide what track and what spring the installation needs.
New doors in Keller
A shop or outbuilding door in Keller is often taller than the standard seven or eight feet, which means high lift track rather than a standard radius. Vinyl stop molding with an integral bulb seal became the usual perimeter detail on openings finished in the 2000s, and the bulb does sealing work that a section edge cannot. Rubber compressed against a door for years takes a set and stops recovering. Section thickness decides where the bulb bears, so the molding goes on new with the door. The garage door covers a large share of the front elevation on most houses, so panel design and color carry more visual weight than most other exterior choices. Doors are sold in series, and the series fixes the panel profile along with the finishes and window options available at a given width. Settling the appearance first narrows the order to one product line. A single door replacement is a half day, two doors a full day.
What that means for a Keller door
Doors ordered in volume for subdivisions through the 1990s and 2000s came with builder grade hardware, usually short stem steel rollers turning in light gauge track. The rough opening sets none of that. Longer stem rollers with sealed bearings and nylon tires fit the same jambs, and track gauge and hinge stock are specified apart from the panel design. Attached garages built in the 1990s normally have drywall on the wall above the opening for fire separation from the house. Torsion hardware bolts through that layer into the header behind it, so the lag screws have to reach solid wood rather than stopping in gypsum. Finding the framing before the bearing plate is drilled matters more here than in a garage with open studs.
Signs you are dealing with this
- Repair costs are approaching the price of a new door
- Panels are dented, rusted through or delaminating
What we check on arrival
- Header, jamb and framing condition behind the existing door
- Whether the existing opener suits the weight of the new door
$1100 to $4500
A standard insulated steel two-car door installed sits in the lower half. Custom sizes, wood or full-view glass doors run above the range.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Keller at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 35 minutes from our Coppell base
- Postcodes covered
- 76244, 76248
- Around
- Keller Town Center, Bear Creek Park, The Keller Pointe
Before we get there
The old door still has loaded springs in it. Removal is the dangerous half of an installation, not the fitting.
About Keller
Outbuildings and shop garages here often need a door taller than the standard seven or eight feet.
Tarrant County. About 35 minutes from our Coppell base.
What that means for a door here
A shop or outbuilding door in Keller is often taller than the standard seven or eight feet, which means high lift track rather than a standard radius.
We work throughout Keller, including the neighbourhoods around Keller Town Center, Bear Creek Park, The Keller Pointe.
Get a price
Tell us about your Keller door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 35 minutes away, and Keller sits in Tarrant County.
A person answers 7am to 11pm.
Questions
New doors in Keller, asked and answered
Do you cover Keller?
Yes. Keller is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 35 minutes from our Coppell base. That covers postcodes 76244, 76248.
What usually fails on a Keller door?
Insulated sections are commonly built at 1 3/8 inches or 2 inches thick, and the thickness sets the joint geometry between sections along with the hinge offset. A thicker section weighs more, so the spring is wound for a different load and the hinge and track package is sized to suit. Section thickness also decides how far the door sits from the jamb seal.
How long does new garage door installation take in Keller?
A single door replacement is a half day, two doors a full day. R value measures resistance to heat flow through the door section itself rather than through the garage as a whole. A polyurethane core bonded to both steel skins reaches a higher R value per inch than expanded polystyrene of the same thickness. The practical effect in a hot climate is a garage that tracks outdoor temperature more slowly.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Keller?
Outbuildings and shop garages here often need a door taller than the standard seven or eight feet. Carriage house styling spread through 2000s construction, and doors in that style are almost always sectionals with overlay applied to the face rather than doors that swing. The overlay boards and the applied strap hardware add weight and stand proud of the section, so clearance to the stop molding and the spring calculation both account for the added material.
Get it fixed
Get a new doors price for your Keller door
Tell us what it is doing. The estimate on site is free.