Jump to a service
Hurst, TX
Garage door cable and track repair in Hurst, Texas
A door hanging crooked, off its rail, or with a cable coiled at the bottom bracket is carrying its load somewhere it was not designed to. That is not a door to keep operating.
A door off its track can fall. Do not run the opener to try to correct it, and keep people and vehicles out from under it until it is secured.
Cables and track in Hurst
A one piece tilt up door swings out as it opens and carries its springs on the jamb, so it behaves nothing like the sectional door most people picture. Rollers should ride in the track with a little clearance behind the wheel rather than pressed against the back of the channel. Track that sits too close binds the door and wears flats on the wheels. Track set too far out lets the wheel climb the lip on the way past the curve. The gap is set at the brackets on the jamb. The top roller sits in a fixture that slides in and out on slotted holes, and that setting is what holds the top section against the header seal. On a door this old the slots are rusted and the bolts have often been overtightened into one position. A top section that leans away from the header at the end of its travel is set wrong there. Most track and cable work is one to two hours.
What that means for a Hurst door
Horizontal track is hung with a slight downward pitch toward the back of the garage so the door settles against the weatherstrip at the header when it closes. The rear hangers carry that geometry and have to land in framing, not in drywall. Track that sags between hangers shows as a door that hesitates at the curve on the way down. Steel rollers with exposed bearings were standard on older installations and wear into an oval, which lets the stem drop in the track. Nylon rollers on sealed bearings run quieter and hold shape longer. Roller stems also bend when a door is forced against an obstruction, and a bent stem walks the roller out of the track on the next cycle.
Signs you are dealing with this
- A cable is loose, frayed, or coiled off the drum
- The door binds, catches or scrapes at the same point every time
What we check on arrival
- Roller stems and bearings on every hinge position
- Bottom bracket condition, which is under permanent tension
$150 to $450
Resetting a door on its track with new rollers is at the low end. Replacing cables, drums and a bent rail section is at the high end.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Hurst at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 30 minutes from our Coppell base
- Postcodes covered
- 76053, 76054
- Around
- North East Mall, Chisholm Park, Hurst Community Park
Before we get there
A door off its track can fall. Do not run the opener to try to correct it, and keep people and vehicles out from under it until it is secured.
About Hurst
One piece tilt up doors and their jamb mounted spring hardware still exist in older Hurst neighbourhoods.
Tarrant County. About 30 minutes from our Coppell base.
What that means for a door here
A one piece tilt up door swings out as it opens and carries its springs on the jamb, so it behaves nothing like the sectional door most people picture.
We work throughout Hurst, including the neighbourhoods around North East Mall, Chisholm Park, Hurst Community Park.
Get a price
Tell us about your Hurst door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 30 minutes away, and Hurst sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Cables and track in Hurst, asked and answered
Do you cover Hurst?
Yes. Hurst is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 30 minutes from our Coppell base. That covers postcodes 76053, 76054.
What usually fails on a Hurst door?
Track is a running surface, not a bearing surface. Grease spread inside the channel collects grit and turns rollers into skids that drag rather than turn. The bearing at the roller stem and the hinge pivots are what take a light lubricant. A clean dry track with a free rolling wheel is quieter than a greased one.
How long does garage door cable and track repair take in Hurst?
Most track and cable work is one to two hours. The lift cable ends at the bottom bracket on each side of the bottom section, and that bracket carries the full pull of the springs whenever the door is closed. Bottom bracket bolts are not general purpose fasteners to loosen for a seal change. On a 16 foot door the two brackets also set how square the bottom edge sits to the floor.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Hurst?
One piece tilt up doors and their jamb mounted spring hardware still exist in older Hurst neighbourhoods. A cable coiled loose at the bottom bracket lost tension while the door was moving. That happens when the door lands on an obstruction and one side keeps unwinding, or when a spring breaks mid travel. Rewinding the same cable ignores why it came off, since a scored drum or a bent bottom bracket will unseat it again.
Get it fixed
Get a cables and track price for your Hurst door
Tell us what it is doing. The estimate on site is free.