Jump to a service
Hurst, TX
Garage door opener repair and installation in Hurst, Texas
An opener that runs without moving the door, or sends it back up on the way down, is usually a stripped gear, a disconnected trolley or a photo eye out of alignment rather than a dead motor.
Openers in Hurst
A one piece tilt up door swings out as it opens and carries its springs on the jamb, so it behaves nothing like the sectional door most people picture. Openers built before 1993 predate the federal requirement for photo eye entrapment protection, so the only reversal mechanism is a mechanical force setting that drifts as the door ages. That gap cannot be closed by replacing a board or a gear. Where a garage still runs one of these units, the safety question is answered by replacement rather than repair. Photo eyes sit within six inches of the floor on both jambs and have to face each other squarely. Low winter sun entering a single width opening can wash out the receiving lens and read as a blocked beam, which shows up as a door that reverses only at certain hours. A steady indicator light confirms alignment. Repairs run about an hour, a full replacement two to three.
What that means for a Hurst door
Chain drive openers pull the trolley with a metal chain over a sprocket and are the loudest of the common types. Belt drive substitutes a reinforced rubber belt and runs noticeably quieter. Screw drive turns a threaded steel rod with fewer moving parts, though its lubricant thickens in cold weather and the unit slows until it warms. The header bracket at the front of the rail absorbs the entire pulling load of the opener and needs to land in structural framing above the opening. On older builder stock it was frequently lagged into trim or into a drywall return instead. A bracket beginning to pull loose shows as a rail that lifts at the front end on the up cycle.
Signs you are dealing with this
- The opener motor runs but the door stays put
- The door closes partway then reverses back open
What we check on arrival
- Travel limit and force settings against the actual door
- Remote and keypad programming, and rolling code security
$175 to $700
A sensor alignment or limit adjustment is at the bottom of the range. A new belt-drive or wall-mount opener installed is at the top.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Hurst at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 30 minutes from our Coppell base
- Postcodes covered
- 76053, 76054
- Around
- North East Mall, Chisholm Park, Hurst Community Park
Before we get there
Never disable or bypass the photo eyes to make a door close. They are federally required entrapment protection, and a door that will not close is telling you something is wrong.
About Hurst
One piece tilt up doors and their jamb mounted spring hardware still exist in older Hurst neighbourhoods.
Tarrant County. About 30 minutes from our Coppell base.
What that means for a door here
A one piece tilt up door swings out as it opens and carries its springs on the jamb, so it behaves nothing like the sectional door most people picture.
We work throughout Hurst, including the neighbourhoods around North East Mall, Chisholm Park, Hurst Community Park.
How garage door opener repair and installation works, in full
Get a price
Tell us about your Hurst door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 30 minutes away, and Hurst sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Openers in Hurst, asked and answered
Do you cover Hurst?
Yes. Hurst is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 30 minutes from our Coppell base. That covers postcodes 76053, 76054.
What usually fails on a Hurst door?
Exterior keypads mount on the jamb and speak to the same receiver as the remotes, so a keypad that has lost its code is reprogrammed at the learn button on the opener head rather than at the wall station. The battery compartment faces weather and corrodes, and crusted contacts account for a keypad that answers only sometimes in cold conditions.
How long does garage door opener repair and installation take in Hurst?
Repairs run about an hour, a full replacement two to three. An opener from the 1970s answers a transmitter code that never varies, and the head has a pair of low voltage terminals for the wall button. Wiring a separate rolling code receiver to those terminals gives the door current transmitters while the motor stays in place. The original fixed code stays valid unless the internal receiver is disabled, so old remotes keep working.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Hurst?
One piece tilt up doors and their jamb mounted spring hardware still exist in older Hurst neighbourhoods. The opener arm pulls against one point of the top section, and across a sixteen foot span that load has to be spread out. A reinforcement bracket bolted through the panel and a horizontal strut behind it carry the pull into the end stiles. Without that backing the arm fasteners work their way through thin steel and the top edge bows inward.
Get it fixed
Get a openers price for your Hurst door
Tell us what it is doing. The estimate on site is free.