Jump to a service
Hurst, TX
Garage door panel replacement in Hurst, Texas
One damaged section can often be swapped without replacing the whole door. Whether it can comes down to whether the manufacturer still makes that panel, in that design, in that colour.
Panels in Hurst
A one piece tilt up door swings out as it opens and carries its springs on the jamb, so it behaves nothing like the sectional door most people picture. Matching a new section to a painted door is a different job from matching a factory finish. Steel doors that have been repainted carry whatever coating was brushed or rolled on, and the new section arrives with its baked factory color underneath. Adhesion is the issue rather than color, so the factory coating is scuffed and primed before a topcoat goes over it. Panel designs are discontinued on a normal product cycle, so a 16 foot door fitted ten or fifteen years ago may have no current equivalent section. Colors drift as well. A white from one production run is rarely the same white as a run years later, and on a wide door a new section sits directly beside old ones where the difference is easiest to see. A single panel swap is usually two to three hours.
What that means for a Hurst door
A cracked window in a door section does not always mean the section is finished. Window inserts are frames that clip or screw into a cutout, and the glazing inside them is a separate part, so a broken pane can often be dealt with without touching the steel around it. Insert frames do fade and go brittle, which is a separate replacement. Removing an intermediate section means the door has to come apart around it. The spring is unwound so the cables go slack, the sections above are supported or lifted clear, then the hinges on both edges of the damaged section are unbolted. Rollers stay in the track while the section slides out sideways on a door this wide.
Signs you are dealing with this
- An insurance adjuster has asked for a repair estimate
- A vehicle backed into the bottom section
What we check on arrival
- Hinge and strut condition at the damaged section
- Colour and finish match against the weathered existing sections
$350 to $1400
One section on a common current door line is at the low end. Multiple sections, or a discontinued design that needs a full-door match, runs higher.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Hurst at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 30 minutes from our Coppell base
- Postcodes covered
- 76053, 76054
- Around
- North East Mall, Chisholm Park, Hurst Community Park
Before we get there
A dented section can hide a bent strut or hinge behind it. Replacing the skin without checking the structure puts the load back onto damaged parts.
About Hurst
One piece tilt up doors and their jamb mounted spring hardware still exist in older Hurst neighbourhoods.
Tarrant County. About 30 minutes from our Coppell base.
What that means for a door here
A one piece tilt up door swings out as it opens and carries its springs on the jamb, so it behaves nothing like the sectional door most people picture.
We work throughout Hurst, including the neighbourhoods around North East Mall, Chisholm Park, Hurst Community Park.
Get a price
Tell us about your Hurst door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 30 minutes away, and Hurst sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Panels in Hurst, asked and answered
Do you cover Hurst?
Yes. Hurst is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 30 minutes from our Coppell base. That covers postcodes 76053, 76054.
What usually fails on a Hurst door?
An impact hard enough to fold a section usually moved the door in its track at the same time. Track that has been kinked at roller height will mark a new section the same way the old one was marked, and a flattened roller does the same. Sighting down the vertical track for straightness and spinning each roller by hand comes before the replacement goes in.
How long does garage door panel replacement take in Hurst?
A single panel swap is usually two to three hours. Sectional doors built through the 1970s and 1980s were often faced in hardboard on a wood frame rather than in steel. Those panels swell from the bottom edge up once the paint film breaks, and the swelling delaminates the face. Replacement sections for them are rarely available, so a damaged panel is either rebuilt from stock or the door is replaced.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Hurst?
One piece tilt up doors and their jamb mounted spring hardware still exist in older Hurst neighbourhoods. A one piece tilt up door is a single slab on a pivot or jamb hardware, so there are no sections to swap. Damage to the face is repaired in place, by straightening or patching the affected area, or the whole door is replaced. Older tilt up doors are often wood framed, which means a rotted stile or rail can be rebuilt rather than replaced whole.
Get it fixed
Get a panels price for your Hurst door
Tell us what it is doing. The estimate on site is free.