Jump to a service
Hurst, TX
Commercial garage door service in Hurst, Texas
Rolling steel, sectional and dock equipment fail differently from a house door, because they cycle twenty or thirty times a day rather than four. Downtime, not the part, is usually the real cost.
A rolling steel door carries its spring inside the barrel at a tension far above a residential torsion spring. Barrel work is not a maintenance task.
Commercial in Hurst
A one piece tilt up door swings out as it opens and carries its springs on the jamb, so it behaves nothing like the sectional door most people picture. Shop and workshop doors of that age were often hung on three inch track where a house door uses two inch, and the two families do not share rollers or hinges. A roller stem cut for the narrower channel rattles in the wider one. Track width is read across the open face of the channel before any hardware is ordered. A personnel door beside the bay opening keeps foot traffic off the main door, and every trip it absorbs is a cycle the spring does not spend. Where no side door exists, the large door gets opened for a person carrying a box. That pattern is what wears out a residential specification door on a working site. Varies by door type, quoted after the site assessment.
What that means for a Hurst door
Fire rated curtains of that age are commonly held by a fusible link that has to reach its melting point before anything moves, so smoke on its own will not close the door. Release triggered from the alarm panel is a later arrangement. The link is a consumable as well, replaced after it operates rather than reset like a switch. Wide openings run two springs on one shaft, and the shaft passes through a center bearing plate lagged to the header between them. On longer shafts a coupling joins two lengths, and a coupling that has loosened lets one half turn slightly before the other. The symptom is a door that starts crooked and squares up partway through the lift.
Signs you are dealing with this
- A high-speed door has lost its position or keeps faulting
- Chain hoist or motor operator failure on a heavy door
What we check on arrival
- Counterbalance spring tension against the actual door weight
- Cycle count and whether the current hardware suits the usage
$300 to $6000
A service call and adjustment is at the low end. Rolling steel door replacement and dock equipment work runs to the top of the range and beyond.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Hurst at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 30 minutes from our Coppell base
- Postcodes covered
- 76053, 76054
- Around
- North East Mall, Chisholm Park, Hurst Community Park
Before we get there
A rolling steel door carries its spring inside the barrel at a tension far above a residential torsion spring. Barrel work is not a maintenance task.
About Hurst
One piece tilt up doors and their jamb mounted spring hardware still exist in older Hurst neighbourhoods.
Tarrant County. About 30 minutes from our Coppell base.
What that means for a door here
A one piece tilt up door swings out as it opens and carries its springs on the jamb, so it behaves nothing like the sectional door most people picture.
We work throughout Hurst, including the neighbourhoods around North East Mall, Chisholm Park, Hurst Community Park.
Get a price
Tell us about your Hurst door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 30 minutes away, and Hurst sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Commercial in Hurst, asked and answered
Do you cover Hurst?
Yes. Hurst is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 30 minutes from our Coppell base. That covers postcodes 76053, 76054.
What usually fails on a Hurst door?
Photo eyes have been required on residential garage door openers sold in the United States since 1993, so an opener older than that has no external entrapment protection and relies on a mechanical force reversal alone. Older light industrial buildings often still run equipment from that period on doors that now cycle far more than they did. Parts support for those operators is thin.
How long does commercial garage door service take in Hurst?
Varies by door type, quoted after the site assessment. Light gauge single layer steel doors turn up on small workshop and storage units as often as on houses. The door looks the same from outside, but the duty is not. Panel skins dent from forklift and trolley contact, and the hinges wear at a rate set by the traffic rather than by the age of the building.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Hurst?
One piece tilt up doors and their jamb mounted spring hardware still exist in older Hurst neighbourhoods. Single bay openings are the standard size for small trade units and converted workshop bays, which is why a door of that width often ends up doing commercial work behind a residential specification. The tell is wear that does not match the age of the door. Elongated hinge holes and gaps opening between the spring coils show up years earlier than the install date would suggest.
Get it fixed
Get a commercial price for your Hurst door
Tell us what it is doing. The estimate on site is free.