Jump to a service
Hurst, TX
Garage door tune up and maintenance in Hurst, Texas
A service visit covers rollers, hinges, bearings, spring condition, door balance and the safety reverse. It is the cheapest way to find the part that would otherwise strand somebody.
Tune up in Hurst
A one piece tilt up door swings out as it opens and carries its springs on the jamb, so it behaves nothing like the sectional door most people picture. Steel on a 1970s door was rolled heavier than the sheet on a builder door made now, because material cost fell over the decades between them. The older panel dents less and weighs more, which is why a section swapped in from current stock changes what the counterbalance is holding. Hardware fastener patterns from that period also differ from what a parts shelf carries. One piece tilt up doors swing out on their way up, and their springs sit on the side jambs rather than on a shaft above the opening. Maintenance is a different list from a sectional door: pivot points at the hinge arms and the condition of the spring anchor holes in the jamb hardware. Nothing on a tilt door is interchangeable with sectional parts. About an hour for one door.
What that means for a Hurst door
Grease on a garage door track collects dust and grit and turns into a lapping paste. The roller then skids along the smear instead of rotating, which flattens the roller and loads the hinge. A dry track with a clean, freely spinning roller runs quieter than a greased one. Wiping the track clean with a rag is the correct maintenance step. Extension springs stretch along the horizontal track above each side of a single bay door rather than winding on a shaft. A safety containment cable threaded through the spring is what stops the pieces from leaving the track when the spring breaks. Retrofit sets are sold for doors built without them, and a spring running with no cable through its center is the thing to look for.
Signs you are dealing with this
- You want to know how much life the springs have left
- The door has become noticeably louder over the past year
What we check on arrival
- Door balance at three positions with the opener disconnected
- Every hinge, roller, bearing and fastener on the door and track
$99 to $199
One door is at the low end. Multiple doors on the same visit are discounted per door.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Hurst at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 30 minutes from our Coppell base
- Postcodes covered
- 76053, 76054
- Around
- North East Mall, Chisholm Park, Hurst Community Park
Before we get there
Lubricate rollers, hinges and springs, never the tracks. Grease on a track collects grit and wears rollers faster than no lubricant at all.
About Hurst
One piece tilt up doors and their jamb mounted spring hardware still exist in older Hurst neighbourhoods.
Tarrant County. About 30 minutes from our Coppell base.
What that means for a door here
A one piece tilt up door swings out as it opens and carries its springs on the jamb, so it behaves nothing like the sectional door most people picture.
We work throughout Hurst, including the neighbourhoods around North East Mall, Chisholm Park, Hurst Community Park.
Get a price
Tell us about your Hurst door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 30 minutes away, and Hurst sits in Tarrant County.
A person answers 7am to 11pm.
Questions
Tune up in Hurst, asked and answered
Do you cover Hurst?
Yes. Hurst is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 30 minutes from our Coppell base. That covers postcodes 76053, 76054.
What usually fails on a Hurst door?
The bottom bracket at each corner anchors the lift cable, so it stays under the spring's full load whenever the door is down. Its fasteners are not general purpose hardware to be removed during cleaning. Cable condition is read at that bracket too, since the loop over the pin is where broken strands show first and where rust from a damp slab starts.
How long does garage door tune up and maintenance take in Hurst?
About an hour for one door. Garages built in those decades were sized for narrower cars, and many openings have since been widened or reframed to take something current. The header over a widened opening is the piece to look at, because spring hardware anchors into it. Original jambs are often full thickness lumber that holds a lag screw well, while a later patch may not.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Hurst?
One piece tilt up doors and their jamb mounted spring hardware still exist in older Hurst neighbourhoods. A single bay door is light enough that a failing spring can go unnoticed for a long time, because the opener will still lift it. That is the problem. The motor is doing work the spring should be doing, and gear wear follows. Disconnecting the opener and lifting by hand is the check that separates a spring fault from an opener fault on a small door.
Get it fixed
Get a tune up price for your Hurst door
Tell us what it is doing. The estimate on site is free.