Jump to a service
Garland, TX
Garage door spring replacement in Garland, Texas
A broken torsion spring is the most common reason a door stops lifting. The fix is a matched pair sized to what the door actually weighs, not the cheapest spring that fits the shaft.
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
Springs in Garland
An opener without photo eyes predates the 1993 federal requirement, and in Garland that is still a live category rather than a curiosity. Steel got thinner as the decades passed. A single layer door pressed in the 1970s uses a heavier gauge than a current builder panel of the same size, and it weighs accordingly. Sizing a spring from a chart keyed to door width and height can therefore come out light on an older door. Two doors of identical size from different decades are not the same load. Extension spring assemblies of that vintage fail at the ends more often than in the middle of the coil. The last loop straightens where it hooks the bracket, and the sheave it pulls against seizes on its axle once the grease has dried. A seized sheave puts the stretch of one spring out of step with the other, and the door leans as it lifts. Usually under two hours from arrival.
What that means for a Garland door
Winding cones take steel winding bars sized to the holes in the cone, and anything else, including screwdrivers and rebar, slips out under load. The set screws bite into the shaft itself, so a shaft already dimpled from earlier work gives them less to hold. Chalk drawn along a wound shaft shows at a glance whether a cone has since slipped. A broken torsion spring shows as a gap of an inch or two in the coil, usually visible from the floor by looking at the shaft above the door. The break often announces itself as a single loud bang from an empty garage. After it, the opener may hum and move the trolley while the door stays on the floor.
Signs you are dealing with this
- A visible gap in the coil of the spring above the door
- The door is far too heavy to lift by hand
What we check on arrival
- Whether the existing springs were correctly specified for the door weight
- Cable and drum condition, since a broken spring often damages both
$200 to $450
A standard pair of torsion springs on a two-car door sits mid-range. Oversized, high-cycle or custom-weight doors run higher.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Garland at a glance
- County
- Dallas County
- Drive from our Coppell base
- About 40 minutes from our Coppell base
- Postcodes covered
- 75040, 75041, 75042, 75043, 75044
- Around
- Downtown Garland Square, Lake Ray Hubbard, Firewheel Town Center
Before we get there
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
About Garland
Openers old enough to lack photo eye sensors still turn up regularly in Garland.
Dallas County. About 40 minutes from our Coppell base.
What that means for a door here
An opener without photo eyes predates the 1993 federal requirement, and in Garland that is still a live category rather than a curiosity.
We work throughout Garland, including the neighbourhoods around Downtown Garland Square, Lake Ray Hubbard, Firewheel Town Center.
Get a price
Tell us about your Garland door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 40 minutes away, and Garland sits in Dallas County.
A person answers 7am to 11pm.
Questions
Springs in Garland, asked and answered
Do you cover Garland?
Yes. Garland is in Dallas County, and it is one of the 32 cities covered from the Coppell base. About 40 minutes from our Coppell base. That covers postcodes 75040, 75041, 75042, 75043, 75044.
What usually fails on a Garland door?
Steel loses a little toughness as it gets cold and the grease on the coils thickens, so a spring already near the end of its cycle life often lets go on the first hard freeze of the season rather than on a mild afternoon. The cold does not wear the spring out. It finishes off one that was already close.
How long does garage door spring replacement take in Garland?
Usually under two hours from arrival. A 16 foot torsion assembly rides in an end bearing plate at each side of the opening and usually a center bearing at the anchor bracket. Bearings that have lost their grease squeal on every cycle and let the shaft move in its race. A worn race also lets the shaft wear a groove, and a grooved shaft keeps eating bearings after they are replaced.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Garland?
Openers old enough to lack photo eye sensors still turn up regularly in Garland. Leftover parts on the horizontal track tell whether a door was converted from extension springs to torsion. Pulley brackets and an empty rear hanger near the back of the track are what stays behind. A conversion brings a shaft, end bearing plates, drums and cables with it, so the hardware above the opening is often newer than the door below it.
Get it fixed
Get a springs price for your Garland door
Tell us what it is doing. The estimate on site is free.