Jump to a service
Garland, TX
Garage door cable and track repair in Garland, Texas
A door hanging crooked, off its rail, or with a cable coiled at the bottom bracket is carrying its load somewhere it was not designed to. That is not a door to keep operating.
A door off its track can fall. Do not run the opener to try to correct it, and keep people and vehicles out from under it until it is secured.
Cables and track in Garland
An opener without photo eyes predates the 1993 federal requirement, and in Garland that is still a live category rather than a curiosity. Track is bent steel channel with no moving parts, and a straight length of it from the 1980s does the same job now as it did then. What wears is everything that touches it: roller wheels and hinge pivots. A door of that age often needs those parts and nothing else, provided the channel is still straight and square to the opening. Sectional door hinges are stamped with a number that says where they belong, 1 at the joint nearest the bottom and rising with each joint above it. The number sets how far the roller stem stands off the panel. A hinge fitted in the wrong position pushes that section toward or away from the track and loads one roller against the track lip. Most track and cable work is one to two hours.
What that means for a Garland door
Steel rollers with exposed bearings were standard on older installations and wear into an oval, which lets the stem drop in the track. Nylon rollers on sealed bearings run quieter and hold shape longer. Roller stems also bend when a door is forced against an obstruction, and a bent stem walks the roller out of the track on the next cycle. On an extension spring door the springs hang beside the horizontal tracks and pull against a rear hanger, with a cable running forward over a sheave to the bottom bracket. Track and counterbalance share the same brackets there, so moving a rear hanger to correct track pitch also changes where the spring pulls from. The two adjustments are not independent.
Signs you are dealing with this
- The door is visibly hanging out of the track on one side
- A cable is loose, frayed, or coiled off the drum
What we check on arrival
- Roller stems and bearings on every hinge position
- Bottom bracket condition, which is under permanent tension
$150 to $450
Resetting a door on its track with new rollers is at the low end. Replacing cables, drums and a bent rail section is at the high end.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Garland at a glance
- County
- Dallas County
- Drive from our Coppell base
- About 40 minutes from our Coppell base
- Postcodes covered
- 75040, 75041, 75042, 75043, 75044
- Around
- Downtown Garland Square, Lake Ray Hubbard, Firewheel Town Center
Before we get there
A door off its track can fall. Do not run the opener to try to correct it, and keep people and vehicles out from under it until it is secured.
About Garland
Openers old enough to lack photo eye sensors still turn up regularly in Garland.
Dallas County. About 40 minutes from our Coppell base.
What that means for a door here
An opener without photo eyes predates the 1993 federal requirement, and in Garland that is still a live category rather than a curiosity.
We work throughout Garland, including the neighbourhoods around Downtown Garland Square, Lake Ray Hubbard, Firewheel Town Center.
Get a price
Tell us about your Garland door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 40 minutes away, and Garland sits in Dallas County.
A person answers 7am to 11pm.
Questions
Cables and track in Garland, asked and answered
Do you cover Garland?
Yes. Garland is in Dallas County, and it is one of the 32 cities covered from the Coppell base. About 40 minutes from our Coppell base. That covers postcodes 75040, 75041, 75042, 75043, 75044.
What usually fails on a Garland door?
Horizontal track in older garages is often hung on perforated angle iron dropped from the joists. Perforated stock flexes under load and lets the track sway as the door moves, which walks rollers toward the edge of the channel. Solid angle braced back at a diagonal holds the track still. Fasteners that have worked loose in old joist timber show as movement at the rear hanger.
How long does garage door cable and track repair take in Garland?
Most track and cable work is one to two hours. Track is a running surface, not a bearing surface. Grease spread inside the channel collects grit and turns rollers into skids that drag rather than turn. The bearing at the roller stem and the hinge pivots are what take a light lubricant. A clean dry track with a free rolling wheel is quieter than a greased one.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Garland?
Openers old enough to lack photo eye sensors still turn up regularly in Garland. The top roller sits in a fixture that slides in and out on slotted holes, and that setting is what holds the top section against the header seal. On a door this old the slots are rusted and the bolts have often been overtightened into one position. A top section that leans away from the header at the end of its travel is set wrong there.
Get it fixed
Get a cables and track price for your Garland door
Tell us what it is doing. The estimate on site is free.