Jump to a service
Garland, TX
Garage door panel replacement in Garland, Texas
One damaged section can often be swapped without replacing the whole door. Whether it can comes down to whether the manufacturer still makes that panel, in that design, in that colour.
Panels in Garland
An opener without photo eyes predates the 1993 federal requirement, and in Garland that is still a live category rather than a curiosity. A section is ordered by its position in the door as well as by width and height. A bottom section is built with the cable brackets and the weather seal retainer already fitted; a top section is drilled for the operator bracket. Measuring the existing section rather than the opening gives the width to order, since sections are built narrower than the rough opening. Sections on doors of the 1980s often have a cutout stamped in the face for a center lock handle, with the spindle passing through to a bar behind. Current sections are supplied without that cutout. Where the lock section is the damaged one, the new panel comes in blank, and the old handle has no home unless the steel is drilled. A single panel swap is usually two to three hours.
What that means for a Garland door
Whether a single section can be ordered starts with the manufacturer label, usually a sticker on the inside of the top or bottom section near an end stile. It carries the maker, the model line and a date, and without it the door has to be identified from panel profile and hardware alone. A door still in production is the straightforward case. Sectional doors built through the 1970s and 1980s were often faced in hardboard on a wood frame rather than in steel. Those panels swell from the bottom edge up once the paint film breaks, and the swelling delaminates the face. Replacement sections for them are rarely available, so a damaged panel is either rebuilt from stock or the door is replaced.
Signs you are dealing with this
- A panel is cracked, split or rusting through at the bottom edge
- The door still runs correctly but looks damaged
What we check on arrival
- Colour and finish match against the weathered existing sections
- Whether the impact also bent track or knocked the door out of alignment
$350 to $1400
One section on a common current door line is at the low end. Multiple sections, or a discontinued design that needs a full-door match, runs higher.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Garland at a glance
- County
- Dallas County
- Drive from our Coppell base
- About 40 minutes from our Coppell base
- Postcodes covered
- 75040, 75041, 75042, 75043, 75044
- Around
- Downtown Garland Square, Lake Ray Hubbard, Firewheel Town Center
Before we get there
A dented section can hide a bent strut or hinge behind it. Replacing the skin without checking the structure puts the load back onto damaged parts.
About Garland
Openers old enough to lack photo eye sensors still turn up regularly in Garland.
Dallas County. About 40 minutes from our Coppell base.
What that means for a door here
An opener without photo eyes predates the 1993 federal requirement, and in Garland that is still a live category rather than a curiosity.
We work throughout Garland, including the neighbourhoods around Downtown Garland Square, Lake Ray Hubbard, Firewheel Town Center.
Get a price
Tell us about your Garland door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 40 minutes away, and Garland sits in Dallas County.
A person answers 7am to 11pm.
Questions
Panels in Garland, asked and answered
Do you cover Garland?
Yes. Garland is in Dallas County, and it is one of the 32 cities covered from the Coppell base. About 40 minutes from our Coppell base. That covers postcodes 75040, 75041, 75042, 75043, 75044.
What usually fails on a Garland door?
Older sectional doors were frequently built in five sections to a 7 foot height rather than the four that most current doors use, which makes each section shorter. Section height has to match for hinges to land on the existing lines, so a panel design that looks right in a catalog can still be the wrong depth for the door taking it.
How long does garage door panel replacement take in Garland?
A single panel swap is usually two to three hours. A dent that stops at the skin is cosmetic. A dent that has bowed the strut across the top section or twisted a hinge leaf is structural, and a 16 foot door shows it in motion rather than at rest. Run the door by hand and watch the section edges. A panel that rubs the track or lifts unevenly has damage behind the steel.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Garland?
Openers old enough to lack photo eye sensors still turn up regularly in Garland. Aluminum sectional doors were common in mid century construction, light enough to lift easily and soft enough that a dent stays put. The skin is thin and often a mill or anodized finish, which no painted steel panel will match. Sections for those doors left production long ago, so a damaged one is straightened and filled in place rather than exchanged.
Get it fixed
Get a panels price for your Garland door
Tell us what it is doing. The estimate on site is free.