Jump to a service
Bedford, TX
New garage door installation in Bedford, Texas
A replacement door is a measuring job before it is a shopping decision. Opening width, headroom, backroom and the weight of the door chosen all decide what track and what spring the installation needs.
New doors in Bedford
Bedford is dominated by standard sixteen foot openings, which means parts availability is rarely what decides how quickly a repair finishes. Doors past about nine feet wide normally run a pair of torsion springs on a shaft that crosses the header, with a center bearing plate anchored to the wall between them. That plate is the anchor the springs wind against, so it has to land on solid framing. End bearing plates carry the shaft at each side and set where the cable drums sit. Doors ordered in volume for subdivisions through the 1990s and 2000s came with builder grade hardware, usually short stem steel rollers turning in light gauge track. The rough opening sets none of that. Longer stem rollers with sealed bearings and nylon tires fit the same jambs, and track gauge and hinge stock are specified apart from the panel design. A single door replacement is a half day, two doors a full day.
What that means for a Bedford door
A wall control belongs at least 5 feet above the floor so the door cannot be run by a small child standing under it. Buttons put in during the 1980s sit at light switch height beside the entry door more often than not. Fresh low voltage wire is run up to the higher position rather than spliced onto the old pair. Openings of the 1970s and 1980s were commonly closed with doors on extension springs stretched along the horizontal tracks and anchored at the rear hangers. Converting to torsion during installation puts a shaft and a spring anchor pad across the header. The lifting load then goes into the wall above the opening rather than back into the ceiling framing.
Signs you are dealing with this
- You are selling and the door is the first thing buyers see
- Repair costs are approaching the price of a new door
What we check on arrival
- Whether the existing opener suits the weight of the new door
- Any homeowners association requirements on style and color
$1100 to $4500
A standard insulated steel two-car door installed sits in the lower half. Custom sizes, wood or full-view glass doors run above the range.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Bedford at a glance
- County
- Tarrant County
- Drive from our Coppell base
- About 30 minutes from our Coppell base
- Postcodes covered
- 76021, 76022
- Around
- Boys Ranch Park, Bedford Splash, Old Bedford School
Before we get there
The old door still has loaded springs in it. Removal is the dangerous half of an installation, not the fitting.
About Bedford
Standard sixteen foot two car openings dominate here, so replacement parts are rarely a sourcing problem.
Tarrant County. About 30 minutes from our Coppell base.
What that means for a door here
Bedford is dominated by standard sixteen foot openings, which means parts availability is rarely what decides how quickly a repair finishes.
We work throughout Bedford, including the neighbourhoods around Boys Ranch Park, Bedford Splash, Old Bedford School.
Get a price
Tell us about your Bedford door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 30 minutes away, and Bedford sits in Tarrant County.
A person answers 7am to 11pm.
Questions
New doors in Bedford, asked and answered
Do you cover Bedford?
Yes. Bedford is in Tarrant County, and it is one of the 32 cities covered from the Coppell base. About 30 minutes from our Coppell base. That covers postcodes 76021, 76022.
What usually fails on a Bedford door?
Vertical track on a 16 foot opening bolts to the jamb, so the jamb has to be sound wood fastened to the framing rather than trim tacked over masonry. Rot at the base is common where the jamb meets the slab. A jamb that is out of plumb pulls the track with it, and the door then binds on one side as it travels.
How long does new garage door installation take in Bedford?
A single door replacement is a half day, two doors a full day. Insulated sections are commonly built at 1 3/8 inches or 2 inches thick, and the thickness sets the joint geometry between sections along with the hinge offset. A thicker section weighs more, so the spring is wound for a different load and the hinge and track package is sized to suit. Section thickness also decides how far the door sits from the jamb seal.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Bedford?
Standard sixteen foot two car openings dominate here, so replacement parts are rarely a sourcing problem. Glazing changes the order beyond appearance. Window inserts sit in a cutout, usually in the top section, and the glass adds weight at the same place the operator bracket already loads the door. Insulated glass units weigh more than single pane acrylic. A cutout also removes stamped area from the panel, so the section leans harder on its strut to stay flat.
Get it fixed
Get a new doors price for your Bedford door
Tell us what it is doing. The estimate on site is free.