Jump to a service
Irving, TX
Garage door panel replacement in Irving, Texas
One damaged section can often be swapped without replacing the whole door. Whether it can comes down to whether the manufacturer still makes that panel, in that design, in that colour.
Panels in Irving
A good share of south and central Irving still runs openers that predate 1993, which is the year photo eye entrapment protection became mandatory. Openers added to doors of the 1980s were frequently bolted through the top section skin with no reinforcement bracket behind it, because the door had not been built with an operator in mind. The holes elongate and the steel tears around them. A section replaced for that reason takes a proper strut and bracket, or the new panel goes the same way. Removing an intermediate section means the door has to come apart around it. The spring is unwound so the cables go slack, the sections above are supported or lifted clear, then the hinges on both edges of the damaged section are unbolted. Rollers stay in the track while the section slides out sideways on a door this wide. A single panel swap is usually two to three hours.
What that means for a Irving door
Steel that has been stretched by an impact will not come back to its original shape, which is the line between pushing a shallow dimple out and replacing the section. A crease that runs across a stamped rib has stretched the metal along that line. Filler bridges the low spot but sits on a panel that flexes every cycle, so it eventually cracks at the edge. Older sectional doors were frequently built in five sections to a 7 foot height rather than the four that most current doors use, which makes each section shorter. Section height has to match for hinges to land on the existing lines, so a panel design that looks right in a catalog can still be the wrong depth for the door taking it.
Signs you are dealing with this
- Hail has dimpled one or two panels but the rest are sound
- A panel is cracked, split or rusting through at the bottom edge
What we check on arrival
- Whether the impact also bent track or knocked the door out of alignment
- Manufacturer, model and panel design, to confirm a match is available
$350 to $1400
One section on a common current door line is at the low end. Multiple sections, or a discontinued design that needs a full-door match, runs higher.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Irving at a glance
- County
- Dallas County
- Drive from our Coppell base
- About 15 minutes from our Coppell base
- Postcodes covered
- 75038, 75060, 75061, 75062
- Around
- Irving Heritage District, Toyota Music Factory, Irving Mall
Before we get there
A dented section can hide a bent strut or hinge behind it. Replacing the skin without checking the structure puts the load back onto damaged parts.
About Irving
South and central Irving hold a lot of single-width doors and older chain drive openers with no rolling code security.
Dallas County. About 15 minutes from our Coppell base.
What that means for a door here
A good share of south and central Irving still runs openers that predate 1993, which is the year photo eye entrapment protection became mandatory.
We work throughout Irving, including the neighbourhoods around Irving Heritage District, Toyota Music Factory, Irving Mall.
Get a price
Tell us about your Irving door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 15 minutes away, and Irving sits in Dallas County.
A person answers 7am to 11pm.
Questions
Panels in Irving, asked and answered
Do you cover Irving?
Yes. Irving is in Dallas County, and it is one of the 32 cities covered from the Coppell base. About 15 minutes from our Coppell base. That covers postcodes 75038, 75060, 75061, 75062.
What usually fails on a Irving door?
Fiberglass faced doors were sold through the 1970s, often with translucent panels that let daylight into the garage. Sun makes the resin yellow and go brittle, so a panel that survived intact can crack while it is being handled. Nothing current is made to those panel sizes, which leaves rebuilding the frame with new material or changing the door.
How long does garage door panel replacement take in Irving?
A single panel swap is usually two to three hours. An impact hard enough to fold a section usually moved the door in its track at the same time. Track that has been kinked at roller height will mark a new section the same way the old one was marked, and a flattened roller does the same. Sighting down the vertical track for straightness and spinning each roller by hand comes before the replacement goes in.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Irving?
South and central Irving hold a lot of single-width doors and older chain drive openers with no rolling code security. An 8 foot wide door usually has four sections, so one damaged section is about a quarter of the visible face. That proportion makes a color or profile mismatch harder to ignore than on a wider door. Narrow sections are lighter to handle, and the spring is sized for the whole door weight, so removing one section still means unloading the springs first.
Get it fixed
Get a panels price for your Irving door
Tell us what it is doing. The estimate on site is free.