Jump to a service
Irving, TX
Garage door opener repair and installation in Irving, Texas
An opener that runs without moving the door, or sends it back up on the way down, is usually a stripped gear, a disconnected trolley or a photo eye out of alignment rather than a dead motor.
Openers in Irving
A good share of south and central Irving still runs openers that predate 1993, which is the year photo eye entrapment protection became mandatory. Openers of the 1980s set their travel with a mechanical limit assembly inside the head, a threaded rod driving two contact arms that trip switches at each end. Adjusting it means turning a shaft with a screwdriver and running the door to check. Later units count motor revolutions electronically and learn travel during a programming cycle, so nothing inside wears out of adjustment. Openers retrofitted into garages of the 1980s and 1990s were often fed through a lampholder adaptor or an extension cord, because the ceiling light was the only power in the building. Manufacturers call for a grounded receptacle within reach of the cord supplied with the unit. A hot adaptor or a warm cord end is reporting a connection working past its rating. Repairs run about an hour, a full replacement two to three.
What that means for a Irving door
The rail runs from the header bracket back to a pair of ceiling hangers, and it should sit centred on the door width and level along its length. A rail hung off centre drags the top section sideways every cycle. Hangers cut from perforated angle flex when they drop straight down, so bracing them at an angle into a second joist steadies the run. A stripped drive gear announces itself. The motor runs at normal speed and pitch while the door does not move, and plastic shavings collect below the opener head. The gear is nylon by design, so it fails before the motor windings do. Light single layer steel doors mask the early stage, because low weight lets a worn gear keep catching.
Signs you are dealing with this
- The wall button works but the remotes do not
- A grinding noise from the motor housing
What we check on arrival
- Photo eye alignment, wiring and indicator lights
- Travel limit and force settings against the actual door
$175 to $700
A sensor alignment or limit adjustment is at the bottom of the range. A new belt-drive or wall-mount opener installed is at the top.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Irving at a glance
- County
- Dallas County
- Drive from our Coppell base
- About 15 minutes from our Coppell base
- Postcodes covered
- 75038, 75060, 75061, 75062
- Around
- Irving Heritage District, Toyota Music Factory, Irving Mall
Before we get there
Never disable or bypass the photo eyes to make a door close. They are federally required entrapment protection, and a door that will not close is telling you something is wrong.
About Irving
South and central Irving hold a lot of single-width doors and older chain drive openers with no rolling code security.
Dallas County. About 15 minutes from our Coppell base.
What that means for a door here
A good share of south and central Irving still runs openers that predate 1993, which is the year photo eye entrapment protection became mandatory.
We work throughout Irving, including the neighbourhoods around Irving Heritage District, Toyota Music Factory, Irving Mall.
How garage door opener repair and installation works, in full
Get a price
Tell us about your Irving door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 15 minutes away, and Irving sits in Dallas County.
A person answers 7am to 11pm.
Questions
Openers in Irving, asked and answered
Do you cover Irving?
Yes. Irving is in Dallas County, and it is one of the 32 cities covered from the Coppell base. About 15 minutes from our Coppell base. That covers postcodes 75038, 75060, 75061, 75062.
What usually fails on a Irving door?
Chain drive was the residential default through the 1980s, and the trolley is moved by a loop of chain joined to a cable and tensioned at a threaded take up. Chain stretches with age. A loop sagging below the rail slaps on start and lets the carriage snatch before the door moves. Over tightening loads the sprocket bearing and the drive gear instead.
How long does garage door opener repair and installation take in Irving?
Repairs run about an hour, a full replacement two to three. The header bracket at the front of the rail absorbs the entire pulling load of the opener and needs to land in structural framing above the opening. On older builder stock it was frequently lagged into trim or into a drywall return instead. A bracket beginning to pull loose shows as a rail that lifts at the front end on the up cycle.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Irving?
South and central Irving hold a lot of single-width doors and older chain drive openers with no rolling code security. The emergency release disconnects the trolley from the carriage so a door can be raised by hand during a power cut. Pulling it while the door is down is the safe order, since releasing a raised door on weak springs lets the full weight drop. The carriage re-engages on its own when the opener next runs the trolley back over it.
Get it fixed
Get a openers price for your Irving door
Tell us what it is doing. The estimate on site is free.