Jump to a service
Irving, TX
Garage door cable and track repair in Irving, Texas
A door hanging crooked, off its rail, or with a cable coiled at the bottom bracket is carrying its load somewhere it was not designed to. That is not a door to keep operating.
A door off its track can fall. Do not run the opener to try to correct it, and keep people and vehicles out from under it until it is secured.
Cables and track in Irving
A good share of south and central Irving still runs openers that predate 1993, which is the year photo eye entrapment protection became mandatory. Track is bent steel channel with no moving parts, and a straight length of it from the 1980s does the same job now as it did then. What wears is everything that touches it: roller wheels and hinge pivots. A door of that age often needs those parts and nothing else, provided the channel is still straight and square to the opening. A bottom seal sits in a retainer along the lower edge and can freeze to a wet slab overnight. When the opener pulls against a door stuck to the floor, the top of the door moves while the bottom does not, and the cables unwind off the drums. Breaking the seal free by hand before running the opener avoids that. Most track and cable work is one to two hours.
What that means for a Irving door
A sectional door's track comes apart at bolted joints where the vertical meets the curve and the curve meets the horizontal run. Those joints are where alignment is lost first, because each one can slip a little under load. Pulling a slipped joint back into line and tightening it often settles a door that was thought to need new track. A cable coiled loose at the bottom bracket lost tension while the door was moving. That happens when the door lands on an obstruction and one side keeps unwinding, or when a spring breaks mid travel. Rewinding the same cable ignores why it came off, since a scored drum or a bent bottom bracket will unseat it again.
Signs you are dealing with this
- The rail has a visible bend or a gap at a joint
- The door is visibly hanging out of the track on one side
What we check on arrival
- Vertical and horizontal track for bends, spread and loose fasteners
- Roller stems and bearings on every hinge position
$150 to $450
Resetting a door on its track with new rollers is at the low end. Replacing cables, drums and a bent rail section is at the high end.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Irving at a glance
- County
- Dallas County
- Drive from our Coppell base
- About 15 minutes from our Coppell base
- Postcodes covered
- 75038, 75060, 75061, 75062
- Around
- Irving Heritage District, Toyota Music Factory, Irving Mall
Before we get there
A door off its track can fall. Do not run the opener to try to correct it, and keep people and vehicles out from under it until it is secured.
About Irving
South and central Irving hold a lot of single-width doors and older chain drive openers with no rolling code security.
Dallas County. About 15 minutes from our Coppell base.
What that means for a door here
A good share of south and central Irving still runs openers that predate 1993, which is the year photo eye entrapment protection became mandatory.
We work throughout Irving, including the neighbourhoods around Irving Heritage District, Toyota Music Factory, Irving Mall.
Get a price
Tell us about your Irving door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 15 minutes away, and Irving sits in Dallas County.
A person answers 7am to 11pm.
Questions
Cables and track in Irving, asked and answered
Do you cover Irving?
Yes. Irving is in Dallas County, and it is one of the 32 cities covered from the Coppell base. About 15 minutes from our Coppell base. That covers postcodes 75038, 75060, 75061, 75062.
What usually fails on a Irving door?
Steel rollers with exposed bearings were standard on older installations and wear into an oval, which lets the stem drop in the track. Nylon rollers on sealed bearings run quieter and hold shape longer. Roller stems also bend when a door is forced against an obstruction, and a bent stem walks the roller out of the track on the next cycle.
How long does garage door cable and track repair take in Irving?
Most track and cable work is one to two hours. Sectional door hinges are stamped with a number that says where they belong, 1 at the joint nearest the bottom and rising with each joint above it. The number sets how far the roller stem stands off the panel. A hinge fitted in the wrong position pushes that section toward or away from the track and loads one roller against the track lip.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Irving?
South and central Irving hold a lot of single-width doors and older chain drive openers with no rolling code security. Track is a running surface, not a bearing surface. Grease spread inside the channel collects grit and turns rollers into skids that drag rather than turn. The bearing at the roller stem and the hinge pivots are what take a light lubricant. A clean dry track with a free rolling wheel is quieter than a greased one.
Get it fixed
Get a cables and track price for your Irving door
Tell us what it is doing. The estimate on site is free.