Jump to a service
Mesquite, TX
Garage door cable and track repair in Mesquite, Texas
A door hanging crooked, off its rail, or with a cable coiled at the bottom bracket is carrying its load somewhere it was not designed to. That is not a door to keep operating.
A door off its track can fall. Do not run the opener to try to correct it, and keep people and vehicles out from under it until it is secured.
Cables and track in Mesquite
A single layer steel door from the 1970s dents under hail that a modern insulated door shrugs off, and Mesquite still has a lot of them. Track is bent steel channel with no moving parts, and a straight length of it from the 1980s does the same job now as it did then. What wears is everything that touches it: roller wheels and hinge pivots. A door of that age often needs those parts and nothing else, provided the channel is still straight and square to the opening. Horizontal track is hung with a slight downward pitch toward the back of the garage so the door settles against the weatherstrip at the header when it closes. The rear hangers carry that geometry and have to land in framing, not in drywall. Track that sags between hangers shows as a door that hesitates at the curve on the way down. Most track and cable work is one to two hours.
What that means for a Mesquite door
A cable coiled loose at the bottom bracket lost tension while the door was moving. That happens when the door lands on an obstruction and one side keeps unwinding, or when a spring breaks mid travel. Rewinding the same cable ignores why it came off, since a scored drum or a bent bottom bracket will unseat it again. Track and brackets on installations of that age were often drilled on site, so the holes in the jamb follow no factory pattern. New track comes punched to current spacing and rarely lines up with what is already in the wood. Replacing one damaged vertical section usually means new holes in a jamb that already has old ones, so the work starts from a fresh plumb line.
Signs you are dealing with this
- The door binds, catches or scrapes at the same point every time
- Rollers are jumping out of the rail at the curve
What we check on arrival
- Vertical and horizontal track for bends, spread and loose fasteners
- Roller stems and bearings on every hinge position
$150 to $450
Resetting a door on its track with new rollers is at the low end. Replacing cables, drums and a bent rail section is at the high end.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Mesquite at a glance
- County
- Dallas County
- Drive from our Coppell base
- About 45 minutes from our Coppell base
- Postcodes covered
- 75149, 75150, 75180, 75181, 75182
- Around
- Mesquite Rodeo, Town East Mall, Mesquite Arts Center
Before we get there
A door off its track can fall. Do not run the opener to try to correct it, and keep people and vehicles out from under it until it is secured.
About Mesquite
Single layer steel doors from the 1970s and 1980s are still widespread here.
Dallas County. About 45 minutes from our Coppell base.
What that means for a door here
A single layer steel door from the 1970s dents under hail that a modern insulated door shrugs off, and Mesquite still has a lot of them.
We work throughout Mesquite, including the neighbourhoods around Mesquite Rodeo, Town East Mall, Mesquite Arts Center.
Get a price
Tell us about your Mesquite door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 45 minutes away, and Mesquite sits in Dallas County.
A person answers 7am to 11pm.
Questions
Cables and track in Mesquite, asked and answered
Do you cover Mesquite?
Yes. Mesquite is in Dallas County, and it is one of the 32 cities covered from the Coppell base. About 45 minutes from our Coppell base. That covers postcodes 75149, 75150, 75180, 75181, 75182.
What usually fails on a Mesquite door?
Track is a running surface, not a bearing surface. Grease spread inside the channel collects grit and turns rollers into skids that drag rather than turn. The bearing at the roller stem and the hinge pivots are what take a light lubricant. A clean dry track with a free rolling wheel is quieter than a greased one.
How long does garage door cable and track repair take in Mesquite?
Most track and cable work is one to two hours. A 16 foot door runs a cable and a drum at each end of the torsion shaft, and both drums have to hold the same number of wraps. If one set screw slips, that side rises faster, the door racks in the opening, and a roller leaves the track. Correcting it means resetting the wrap count on both drums, since the track itself is often undamaged.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Mesquite?
Single layer steel doors from the 1970s and 1980s are still widespread here. Horizontal track in older garages is often hung on perforated angle iron dropped from the joists. Perforated stock flexes under load and lets the track sway as the door moves, which walks rollers toward the edge of the channel. Solid angle braced back at a diagonal holds the track still. Fasteners that have worked loose in old joist timber show as movement at the rear hanger.
Get it fixed
Get a cables and track price for your Mesquite door
Tell us what it is doing. The estimate on site is free.