Jump to a service
Highland Village, TX
Garage door spring replacement in Highland Village, Texas
A broken torsion spring is the most common reason a door stops lifting. The fix is a matched pair sized to what the door actually weighs, not the cheapest spring that fits the shaft.
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
Springs in Highland Village
Larger doors and open lake exposure find a weak track bracket faster than either would on its own. Wind load ratings moved into building codes after the storm damage of the early 1990s, and doors built to them became common through the following decade. A rated door carries extra struts across the sections and heavier end stiles. That steel adds weight over an unrated door of the same width, and the springs are wound for the door as it was actually built. A broken torsion spring shows as a gap of an inch or two in the coil, usually visible from the floor by looking at the shaft above the door. The break often announces itself as a single loud bang from an empty garage. After it, the opener may hum and move the trolley while the door stays on the floor. Usually under two hours from arrival.
What that means for a Highland Village door
Winding cones take steel winding bars sized to the holes in the cone, and anything else, including screwdrivers and rebar, slips out under load. The set screws bite into the shaft itself, so a shaft already dimpled from earlier work gives them less to hold. Chalk drawn along a wound shaft shows at a glance whether a cone has since slipped. A 16 foot torsion assembly rides in an end bearing plate at each side of the opening and usually a center bearing at the anchor bracket. Bearings that have lost their grease squeal on every cycle and let the shaft move in its race. A worn race also lets the shaft wear a groove, and a grooved shaft keeps eating bearings after they are replaced.
Signs you are dealing with this
- A visible gap in the coil of the spring above the door
- The door is far too heavy to lift by hand
What we check on arrival
- Center bearing plate and end bearing wear
- Door balance after installation, tested by hand at three heights
$200 to $450
A standard pair of torsion springs on a two-car door sits mid-range. Oversized, high-cycle or custom-weight doors run higher.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Highland Village at a glance
- County
- Denton County
- Drive from our Coppell base
- About 25 minutes from our Coppell base
- Postcodes covered
- 75077
- Around
- Lewisville Lake, Unity Park, Doubletree Ranch Park
Before we get there
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
About Highland Village
Larger doors and open lake exposure is a combination that finds weak track brackets.
Denton County. About 25 minutes from our Coppell base.
What that means for a door here
Larger doors and open lake exposure find a weak track bracket faster than either would on its own.
We work throughout Highland Village, including the neighbourhoods around Lewisville Lake, Unity Park, Doubletree Ranch Park.
Get a price
Tell us about your Highland Village door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 25 minutes away, and Highland Village sits in Denton County.
A person answers 7am to 11pm.
Questions
Springs in Highland Village, asked and answered
Do you cover Highland Village?
Yes. Highland Village is in Denton County, and it is one of the 32 cities covered from the Coppell base. About 25 minutes from our Coppell base. That covers postcode 75077.
What usually fails on a Highland Village door?
An insulated steel door carries polystyrene or polyurethane between two skins, which adds weight over a single layer panel of identical width. Springs have to be wound for that extra load. Fitting a spring specified for a lighter door leaves the door heavy at the floor and drifting closed from waist height, and it shortens the opener's working life.
How long does garage door spring replacement take in Highland Village?
Usually under two hours from arrival. The stationary cones of a torsion assembly bolt to a spring anchor bracket fastened into the header above the opening. On a 16 foot door that bracket resists the torque of both springs. Lag screws pulling out of a split or shimmed header let the bracket shift, which shows up as the shaft climbing away from the wall when the door is closed.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Highland Village?
Larger doors and open lake exposure is a combination that finds weak track brackets. Original paperwork rarely survives on a door hung in the 1990s or 2000s, so the replacement spring is specified from the broken one. Wire diameter is found by pushing twenty coils together, measuring that length and dividing by twenty. Inside diameter is often stamped on the cone. Length is measured with the spring at rest, and the wind direction is read off the coil.
Get it fixed
Get a springs price for your Highland Village door
Tell us what it is doing. The estimate on site is free.