Jump to a service
Flower Mound, TX
New garage door installation in Flower Mound, Texas
A replacement door is a measuring job before it is a shopping decision. Opening width, headroom, backroom and the weight of the door chosen all decide what track and what spring the installation needs.
New doors in Flower Mound
A three bay elevation in Flower Mound usually carries two different spring specifications, because the wide door and the two standard doors are not balancing the same weight. Doors past about nine feet wide normally run a pair of torsion springs on a shaft that crosses the header, with a center bearing plate anchored to the wall between them. That plate is the anchor the springs wind against, so it has to land on solid framing. End bearing plates carry the shaft at each side and set where the cable drums sit. Doors ordered in volume for subdivisions through the 1990s and 2000s came with builder grade hardware, usually short stem steel rollers turning in light gauge track. The rough opening sets none of that. Longer stem rollers with sealed bearings and nylon tires fit the same jambs, and track gauge and hinge stock are specified apart from the panel design. A single door replacement is a half day, two doors a full day.
What that means for a Flower Mound door
Carriage house styling spread through 2000s construction, and doors in that style are almost always sectionals with overlay applied to the face rather than doors that swing. The overlay boards and the applied strap hardware add weight and stand proud of the section, so clearance to the stop molding and the spring calculation both account for the added material. Vertical track on a 16 foot opening bolts to the jamb, so the jamb has to be sound wood fastened to the framing rather than trim tacked over masonry. Rot at the base is common where the jamb meets the slab. A jamb that is out of plumb pulls the track with it, and the door then binds on one side as it travels.
Signs you are dealing with this
- Panels are dented, rusted through or delaminating
- The door is a one-piece tilt-up rather than a sectional
What we check on arrival
- Any homeowners association requirements on style and color
- Opening width and height, squared and measured at multiple points
$1100 to $4500
A standard insulated steel two-car door installed sits in the lower half. Custom sizes, wood or full-view glass doors run above the range.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Flower Mound at a glance
- County
- Denton County
- Drive from our Coppell base
- About 20 minutes from our Coppell base
- Postcodes covered
- 75022, 75028
- Around
- The Flower Mound, Grapevine Lake shoreline, Parker Square
Before we get there
The old door still has loaded springs in it. Removal is the dangerous half of an installation, not the fitting.
About Flower Mound
Three bay garages here frequently pair two standard doors with one wider door.
Denton County. About 20 minutes from our Coppell base.
What that means for a door here
A three bay elevation in Flower Mound usually carries two different spring specifications, because the wide door and the two standard doors are not balancing the same weight.
We work throughout Flower Mound, including the neighbourhoods around The Flower Mound, Grapevine Lake shoreline, Parker Square.
Get a price
Tell us about your Flower Mound door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 20 minutes away, and Flower Mound sits in Denton County.
A person answers 7am to 11pm.
Questions
New doors in Flower Mound, asked and answered
Do you cover Flower Mound?
Yes. Flower Mound is in Denton County, and it is one of the 32 cities covered from the Coppell base. About 20 minutes from our Coppell base. That covers postcodes 75022, 75028.
What usually fails on a Flower Mound door?
Vinyl stop molding with an integral bulb seal became the usual perimeter detail on openings finished in the 2000s, and the bulb does sealing work that a section edge cannot. Rubber compressed against a door for years takes a set and stops recovering. Section thickness decides where the bulb bears, so the molding goes on new with the door.
How long does new garage door installation take in Flower Mound?
A single door replacement is a half day, two doors a full day. Insulated sections are commonly built at 1 3/8 inches or 2 inches thick, and the thickness sets the joint geometry between sections along with the hinge offset. A thicker section weighs more, so the spring is wound for a different load and the hinge and track package is sized to suit. Section thickness also decides how far the door sits from the jamb seal.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Flower Mound?
Three bay garages here frequently pair two standard doors with one wider door. Attached garages built in the 1990s normally have drywall on the wall above the opening for fire separation from the house. Torsion hardware bolts through that layer into the header behind it, so the lag screws have to reach solid wood rather than stopping in gypsum. Finding the framing before the bearing plate is drilled matters more here than in a garage with open studs.
Get it fixed
Get a new doors price for your Flower Mound door
Tell us what it is doing. The estimate on site is free.