Jump to a service
Frisco, TX
Garage door spring replacement in Frisco, Texas
A broken torsion spring is the most common reason a door stops lifting. The fix is a matched pair sized to what the door actually weighs, not the cheapest spring that fits the shaft.
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
Springs in Frisco
Frisco's early 2000s boom put openers and rollers into service on the same day, and both tend to reach the end of their life at the same time. Wind load ratings moved into building codes after the storm damage of the early 1990s, and doors built to them became common through the following decade. A rated door carries extra struts across the sections and heavier end stiles. That steel adds weight over an unrated door of the same width, and the springs are wound for the door as it was actually built. A door that runs away from the floor and slaps into the top of its travel is carrying more spring than its weight calls for. At the top the cables go slack on the drums and can jump the groove, and the top section takes the shock each cycle. The mismatch usually traces back to a spring chosen by door size rather than by measured panel weight. Usually under two hours from arrival.
What that means for a Frisco door
The red release cord drops the door off the opener trolley so it can be worked by hand. With a broken spring, that hand is holding the whole door, and a double door in that state is beyond what one person should lift. A door already up when the spring fails should be left up and blocked rather than pulled down. Doors built from the 2000s onward usually carry a manufacturer label inside an end stile or on the back of a section, listing model and serial. That label is the shortest route back to the original hardware specification, including the counterbalance the door left the factory with. Paint on the outside face does not touch it.
Signs you are dealing with this
- The opener strains, hums, or lifts the door a few inches and quits
- The door slams down rather than lowering under control
What we check on arrival
- Spring wire size, inside diameter and length to confirm correct sizing
- Whether the existing springs were correctly specified for the door weight
$200 to $450
A standard pair of torsion springs on a two-car door sits mid-range. Oversized, high-cycle or custom-weight doors run higher.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Frisco at a glance
- County
- Collin County
- Drive from our Coppell base
- About 35 minutes from our Coppell base
- Postcodes covered
- 75033, 75034, 75035, 75036
- Around
- The Star, Frisco Commons, Toyota Stadium
Before we get there
A torsion spring stores enough energy to cause serious injury. It should only be unwound, adjusted or replaced with proper winding bars by someone trained to use them. This is not a do it yourself repair at any skill level.
About Frisco
Homes built during the early 2000s boom are reaching the point where the opener and the rollers wear out together.
Collin County. About 35 minutes from our Coppell base.
What that means for a door here
Frisco's early 2000s boom put openers and rollers into service on the same day, and both tend to reach the end of their life at the same time.
We work throughout Frisco, including the neighbourhoods around The Star, Frisco Commons, Toyota Stadium.
Get a price
Tell us about your Frisco door
If the door is stuck open or will not close, call. That is a security problem and the phone is faster than anything else on this page. We are about 35 minutes away, and Frisco sits in Collin County.
A person answers 7am to 11pm.
Questions
Springs in Frisco, asked and answered
Do you cover Frisco?
Yes. Frisco is in Collin County, and it is one of the 32 cities covered from the Coppell base. About 35 minutes from our Coppell base. That covers postcodes 75033, 75034, 75035, 75036.
What usually fails on a Frisco door?
A 16 foot double door weighs roughly 150 to 250 pounds depending on panel construction, and the torsion assembly above the header carries all of it. Most double doors of this width run a pair of springs on a shared shaft. When one breaks the other is usually near the end of its life, since both were wound the same day and cycled the same number of times.
How long does garage door spring replacement take in Frisco?
Usually under two hours from arrival. Original paperwork rarely survives on a door hung in the 1990s or 2000s, so the replacement spring is specified from the broken one. Wire diameter is found by pushing twenty coils together, measuring that length and dividing by twenty. Inside diameter is often stamped on the cone. Length is measured with the spring at rest, and the wind direction is read off the coil.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Frisco?
Homes built during the early 2000s boom are reaching the point where the opener and the rollers wear out together. A broken torsion spring shows as a gap of an inch or two in the coil, usually visible from the floor by looking at the shaft above the door. The break often announces itself as a single loud bang from an empty garage. After it, the opener may hum and move the trolley while the door stays on the floor.
Get it fixed
Get a springs price for your Frisco door
Tell us what it is doing. The estimate on site is free.