Jump to a service
Farmers Branch, TX
New garage door installation in Farmers Branch, Texas
A replacement door is a measuring job before it is a shopping decision. Opening width, headroom, backroom and the weight of the door chosen all decide what track and what spring the installation needs.
New doors in Farmers Branch
A mid century Farmers Branch opening is frequently under eight feet wide, which is narrower than anything most suppliers now hold as stock. Openings framed in the 1960s sit in a two by four wall, and the jamb was often one board deep, enough for a thin one piece door and no more. A sectional wants jamb depth behind the stop molding for the track brackets and for roller travel, so those jambs are usually furred out with new stock before track goes on. Photo eyes mount on the vertical track brackets near the floor, and the beam sits no higher than 6 inches above it so an obstruction is caught before the door closes on it. Low voltage wire runs from each eye back to the operator head. Older installations often have the eyes clipped high on the jamb, above the range they were meant to cover. A single door replacement is a half day, two doors a full day.
What that means for a Farmers Branch door
Garages framed in the 1950s and 1960s were often built to whatever width suited the plan rather than to a size sold off the shelf today. An opening measuring 15 feet 4 inches, or one whose header sags, has to be corrected before a sectional door will hang square. Track mounts to the jamb, so a leaning jamb puts the door out of line. An 8 foot wide opening was the common single car size for decades, but 9 feet is now the more usual stock width, so an 8 foot door can be a build to order size rather than one held on a shelf. Two 8 foot doors side by side also load the center post, which carries vertical track for both and needs checking before either door is hung.
Signs you are dealing with this
- The door is a one-piece tilt-up rather than a sectional
- The garage is unbearably hot and the door has no insulation
What we check on arrival
- Headroom, backroom and sideroom to confirm which track systems fit
- Header, jamb and framing condition behind the existing door
$1100 to $4500
A standard insulated steel two-car door installed sits in the lower half. Custom sizes, wood or full-view glass doors run above the range.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Farmers Branch at a glance
- County
- Dallas County
- Drive from our Coppell base
- About 20 minutes from our Coppell base
- Postcodes covered
- 75234, 75244
- Around
- Farmers Branch Historical Park, Mustang Crossing, Brookhaven College
Before we get there
The old door still has loaded springs in it. Removal is the dangerous half of an installation, not the fitting.
About Farmers Branch
Mid century garages here often use a single width door under eight feet, a size many suppliers no longer stock as a standard item.
Dallas County. About 20 minutes from our Coppell base.
What that means for a door here
A mid century Farmers Branch opening is frequently under eight feet wide, which is narrower than anything most suppliers now hold as stock.
We work throughout Farmers Branch, including the neighbourhoods around Farmers Branch Historical Park, Mustang Crossing, Brookhaven College.
Get a price
Tell us about your Farmers Branch door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 20 minutes away, and Farmers Branch sits in Dallas County.
A person answers 7am to 11pm.
Questions
New doors in Farmers Branch, asked and answered
Do you cover Farmers Branch?
Yes. Farmers Branch is in Dallas County, and it is one of the 32 cities covered from the Coppell base. About 20 minutes from our Coppell base. That covers postcodes 75234, 75244.
What usually fails on a Farmers Branch door?
Operator type is decided at installation, not after. A trolley unit runs on a rail down the center of the ceiling and needs backroom for that rail. A jackshaft unit mounts on the wall beside the torsion shaft and drives it directly, which frees the ceiling but requires a shaft and bearing arrangement suited to side mounting.
How long does new garage door installation take in Farmers Branch?
A single door replacement is a half day, two doors a full day. Steel thickness on a door is given as a gauge number, and a lower number means thicker steel. A single layer door has one skin doing all the structural work, so gauge is the main thing separating a light panel from one that resists a knock. Thin skins also drum more when the door runs, since there is no core damping the panel.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Farmers Branch?
Mid century garages here often use a single width door under eight feet, a size many suppliers no longer stock as a standard item. Photo eyes have been required on residential garage door openers in the United States since 1993, so an opener older than that has no beam across the opening. A new door changes the weight the opener lifts, and an older unit sized for a light uninsulated door can struggle with an insulated replacement. Checking the opener at the same time avoids a mismatch.
Get it fixed
Get a new doors price for your Farmers Branch door
Tell us what it is doing. The estimate on site is free.