Jump to a service
Allen, TX
New garage door installation in Allen, Texas
A replacement door is a measuring job before it is a shopping decision. Opening width, headroom, backroom and the weight of the door chosen all decide what track and what spring the installation needs.
New doors in Allen
Hail dimpling on an Allen steel panel is cosmetic until it is not, and the deciding question is whether that section is still in production in that colour. Vinyl stop molding with an integral bulb seal became the usual perimeter detail on openings finished in the 2000s, and the bulb does sealing work that a section edge cannot. Rubber compressed against a door for years takes a set and stops recovering. Section thickness decides where the bulb bears, so the molding goes on new with the door. Residential track is usually 2 inch, and it comes in different steel gauges and in a 12 inch or 15 inch radius at the curve. The wider radius needs more headroom but eases the section through the turn. Track spacing off the jamb is set by the graduated brackets, and it decides how firmly the rollers hold the door against the stop molding. A single door replacement is a half day, two doors a full day.
What that means for a Allen door
R value measures resistance to heat flow through the door section itself rather than through the garage as a whole. A polyurethane core bonded to both steel skins reaches a higher R value per inch than expanded polystyrene of the same thickness. The practical effect in a hot climate is a garage that tracks outdoor temperature more slowly. Doors ordered in volume for subdivisions through the 1990s and 2000s came with builder grade hardware, usually short stem steel rollers turning in light gauge track. The rough opening sets none of that. Longer stem rollers with sealed bearings and nylon tires fit the same jambs, and track gauge and hinge stock are specified apart from the panel design.
Signs you are dealing with this
- Repair costs are approaching the price of a new door
- Panels are dented, rusted through or delaminating
What we check on arrival
- Any homeowners association requirements on style and color
- Opening width and height, squared and measured at multiple points
$1100 to $4500
A standard insulated steel two-car door installed sits in the lower half. Custom sizes, wood or full-view glass doors run above the range.
This is a range, not a quote. The exact price comes after we see the door and you approve it before any work starts. Call (469) 281-7750 and describe what it is doing.
Allen at a glance
- County
- Collin County
- Drive from our Coppell base
- About 40 minutes from our Coppell base
- Postcodes covered
- 75002, 75013
- Around
- Allen Event Center, Watters Creek, Celebration Park
Before we get there
The old door still has loaded springs in it. Removal is the dangerous half of an installation, not the fitting.
About Allen
Steel door panels here often carry hail dimpling that owners have lived with for years.
Collin County. About 40 minutes from our Coppell base.
What that means for a door here
Hail dimpling on an Allen steel panel is cosmetic until it is not, and the deciding question is whether that section is still in production in that colour.
We work throughout Allen, including the neighbourhoods around Allen Event Center, Watters Creek, Celebration Park.
Get a price
Tell us about your Allen door
Describe what the door is doing and somebody will call you back. The estimate on site is free. We are about 40 minutes away, and Allen sits in Collin County.
A person answers 7am to 11pm.
Questions
New doors in Allen, asked and answered
Do you cover Allen?
Yes. Allen is in Collin County, and it is one of the 32 cities covered from the Coppell base. About 40 minutes from our Coppell base. That covers postcodes 75002, 75013.
What usually fails on a Allen door?
A new door rarely weighs the same as the one it replaces, and an opener holds force settings tuned to the old weight. After installation the up and down force and the travel limits need resetting, and the safety reverse checked against an obstruction. An insulated section adds weight over a single layer panel, which shows up first as an opener that stalls near the top.
How long does new garage door installation take in Allen?
A single door replacement is a half day, two doors a full day. Attached garages built in the 1990s normally have drywall on the wall above the opening for fire separation from the house. Torsion hardware bolts through that layer into the header behind it, so the lag screws have to reach solid wood rather than stopping in gypsum. Finding the framing before the bearing plate is drilled matters more here than in a garage with open studs.
Is the work guaranteed?
Parts and labour carry a 5 year warranty. The price is agreed before any work starts, and the on site estimate is free.
Is there anything specific about garage doors in Allen?
Steel door panels here often carry hail dimpling that owners have lived with for years. Garage slabs are poured with a slope toward the opening for drainage, and a 16 foot door sits across the whole of that slope. If the floor drops more on one side, a straight bottom section leaves a wedge of daylight at the low corner. A taller bulb seal absorbs some of it. Grinding or a threshold strip handles the rest.
Get it fixed
Get a new doors price for your Allen door
Tell us what it is doing. The estimate on site is free.